22
English(Original instructions)
57. Top cover
58. Screw
59. Spark plug
ASSEMBLY
UNPACKING
This product requires assembly.
Ŷ
Carefully remove the tool and any accessories from
the box. Make sure that all items listed in the packing
list are included.
Ŷ
Inspect the tool carefully to make sure no breakage
or damage occurred during shipping.
Ŷ
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
tool.
Ŷ
If any parts are damaged or missing do not operate
this product until the parts are replaced.
WARNING:
If any parts are damaged or missing do not
operate this product until the parts are replaced.
Failure to heed this warning could result in
serious personal injury.
WARNING:
Do not attempt to modify this product or create
accessories not recommended for use with this
product. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
WARNING:
To prevent accidental starting that could cause
serious personal injury, always disconnect the
engine spark plug wire from the spark plug pack
when assembling parts.
INSTALLING THE POWER HEAD SHAFT TO THE
ATTACHMENT
See Figure 2.
WARNING:
Never install, remove, or adjust any attachment
while power head is running. Failure to stop the
engine can cause serious personal injury.
The attachment connects to the power head shaft by
means of a coupler device.
Ŷ /RRVHQ WKH NQRE RQ WKH FRXSOHU RI WKH SRZHU KHDG
shaft and remove the end cap from the attachment.
Ŷ 3XVK LQ WKH EXWWRQ ORFDWHG RQ WKH DWWDFKPHQW VKDIW
Align the button with the guide recess on the power
head coupler and slide the two shafts together.
Rotate the attachment shaft until the button locks into
the positioning hole.
NOTE:
If the button does not release completely in the
positioning hole, the shafts are not locked into place.
Slightly rotate from side to side until the button is locked
into place.
Ŷ 7LJKWHQWKHNQREVHFXUHO\
WARNING:
Be certain the knob is fully tightened before
operating equipment; check it periodically for
tightness during use to avoid serious personal
injury.
REMOVING THE ATTACHMENT FROM THE POWER
HEAD
For removing or changing the attachment:
Ŷ /RRVHQWKHNQRE
Ŷ 3XVKLQWKHEXWWRQDQGWZLVWWKHVKDIWVWRUHPRYHDQG
separate ends.
ATTACHING THE HANGER CAP
See Figure 3.
There are two ways to hang your attachment for storage.
Ŷ 7RXVHWKHKDQJHUFDSSXVKLQWKHEXWWRQDQGSODFH
the hanger cap over end of the lower end attachment
shaft. Slightly rotate the cap from side to side until the
button locks into place.
Ŷ 7KH VHFRQGDU\ KROH LQ WKH DWWDFKPHQW VKDIW FDQ EH
used for hanging purposes as well.
ATTACHING THE FRONT HANDLE
See Figure 4.
RBC430SESC
Ŷ ,QVWDOOWKHIURQWKDQGOHRQWRWKHWRSVLGHRIWKHGULYH
shaft boom with the barrier bar on the same side as
the recoil starter (compare to product images in figure
sheet or on giftbox)
Ŷ 5HLQVWDOOWKHFODPSDOLJQWKHVFUHZWRWKHVFUHZKROH
on the front handle.
Ŷ 7LJKWHQEROWVVHFXUHO\
RBC430SBSC
NOTE:
The throttle trigger must be mounted to the
operator’s right side.
Ŷ 5HPRYHWKHFODPS
Ŷ 3ODFH WKH KDQGOH LQ WKH EUDFNHW ORFDWHG RQ WKH VKDIW
housing.
Ŷ +ROGWKHVWDPSLQJFODPSDQGDOLJQWKHEROWVLQWRWKH
bracket.
Ŷ $GMXVW WKH KDQGOH EDU IRU EHVW RSHUDWRU FRQWURO LQ D
comfortable upright position.
Ŷ 7LJKWHQ EROWV ZLWK WKH VWDPSLQJ ZUHQFK WR KROG WKH
bike handle securely.