Realtek Ameba-D RTL872 D Series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 494

background image

Memory Protection Unit (MPU)

User Manual All information provided in this document is subject to legal disclaimers. © REALTEK 2019. All rights reserved.

31

31

30

29

…

7

6

5

4

3

2

1

0

BASE

SH

AP[2:1]

XN

R/W

R/W

R/W

R/W

Bit

Name

Access

Description

31:5

BASE

R/W

Base address. Contains bit[31:5] of the lower inclusive limit of the selected MPU memory region.
This value is zero-extended to provide the base address to be checked against.
This field resets to an unknown value on a Warm reset.

4:3

SH

R/W

Shareability. Defines the shareable domain of this region for normal memory.



00: Non-shareable



10: Outer Shareable



11: Inner Shareable



Others: Reserved

For any type of device memory, the value of this field is ignored.
This field resets to an unknown value on a Warm reset.

2:1

AP[2:1]

R/W

Access permissions. Defines the access permissions for this region.



00: Read/write by privileged code only.



01: Read/write by any privileged level.



10: Read-only by privileged code only.



11: Read-only by any privileged level.

This field resets to an unknown value on a Warm reset.

0

XN

R/W

Execute never. Defines whether the code can be executed from this region.



0: Execution is only permitted if read permitted.



1: Execution is not permitted.

This bit resets to an unknown value on a Warm reset.

3.2.5

MPU_RLAR

The MPU_RLAR characteristics are:



Purpose

: Provides indirect read and write access to the limit address of the currently selected MPU region for the selected security state.



Usage constraints

:



Privileged access is permitted only. Unprivileged access generates a BusFault.



This register is word accessible only. Half-word and byte accesses are unpredictable.



Configurations

: This register is always implemented.



Attributes

:



32-bit read/write register located at 0xE000_EDA0.



Secure software can access the Non-Secure view of this register via MPU_RLAR_NS located at 0xE002_EDA0. The location
0xE002_EDA0 is reserved to software executing in Non-Secure state and the debugger.



This register is banked between Security states.



Preface

: This register provides access to the configuration of the MPU region selected by MPU_RNR.REGION for the appropriate security

state. The field description applies to the currently selected region.

31

30

29

…

7

6

5

4

3

2

1

0

LIMIT

RSVD

AttrIndx

EN

R/W

R/W

R/W

Bit

Name

Access

Description

31:5

LIMIT

R/W

Limit address. Contains bit[31:5] of the upper inclusive limit of the selected MPU memory region.
This value is post-fixed with 0x1F to provide the limit address to be checked against.
This field resets to an unknown value on a Warm reset.

4

RSVD

N/A

Reserved

3:1

AttrIndx

R/W

Attribute index. Associates a set of attributes in the MPU_MAIR0 and MPU_MAIR1 register.
This field resets to an unknown value on a Warm reset.

0

EN

R/W

Enable. Region enable.



0: Region is disabled.



1: Region is enabled.

This bit resets to 0 on a Warm reset.

Realtek confidential files

The document authorized to

SZ99iot

2019-05-15 10:08:03

«
...
29
30
31
32
33
...
»

Содержание Ameba-D RTL872 D Series















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ameba-D RTL872 D Series

Бренд: JETWAY Страницы: 46

Бренд: Micrel Страницы: 14

Бренд: Freescale Semiconductor Страницы: 4

Бренд: WinFast Страницы: 75

Бренд: ST Страницы: 22

Бренд: National Semiconductor Страницы: 13

Бренд: Texas Instruments Страницы: 21

Бренд: OLIMEX Страницы: 13

SUPER P4DPL-8GM

Бренд: Supero Страницы: 86

Бренд: Supermicro Страницы: 100

i.MX 8M Mini SODIMM SOM

Бренд: iWave Страницы: 16

Бренд: Supermicro Страницы: 124

Бренд: Gigabyte Страницы: 80

SIDE POWER SRH 240 TC

Бренд: SLEIPNER MOTOR AS Страницы: 28

Бренд: Microchip Technology Страницы: 18

Бренд: SOYO Страницы: 75

Бренд: Abit Страницы: 80

SMART SPMXCA200

Бренд: Spektrum Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды