Realtek Ameba-D RTL872 D Series Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 494

background image

Direct Memory Access Controller (DMAC)

User Manual All information provided in this document is subject to legal disclaimers. © REALTEK 2019. All rights reserved.

151

The contents of each of the five Status registers is ORed to produce a single bit for each interrupt type in the Combined Status register; that is,
StatusInt.

Note

: For interrupts to propagate past the raw* interrupt register stage, CTLx.INT_EN must be set to 1'b1, and the relevant interrupt must be

unmasked in the mask* interrupt register.

9.3.2.3.1

RawBlock, RawDstTran, RawErr, RawSrcTran, RawTfr



Name:

Interrupt Raw Status Registers



Size:

64 bits



Address offset:



RawTfr – 0x2c0



RawBlock – 0x2c8



RawSrcTran – 0x2d0



RawDstTran – 0x2d8



RawErr – 0x2e0



Read/write access:

read/write

Interrupt events are stored in these Raw Interrupt Status registers before masking: RawBlock, RawDstTran, RawErr, RawSrcTran, and RawTfr.
Each Raw Interrupt Status register has a bit allocated per channel; for example, RawTfr[2] is the Channel 2 raw transfer complete interrupt.

Each bit in these registers is cleared by writing a 1 to the corresponding location in the ClearTfr, ClearBlock, ClearSrcTran, ClearDstTran,
ClearErr registers.

Note

: Write access is available to these registers for software testing purposes only. Under normal operation, writes to these registers are not

recommended.

Bit

Name

Access

Reset

Description

63:DMAH_NUM_CHANNELS

RSVD

N/A

0x0

Reserved

DMAH_NUM_CHANNELS-1:0

RAW

R/W

0x0

Raw interrupt status.

9.3.2.3.2

StatusBlock, StatusDstTran, StatusErr, StatusSrcTran, StatusTfr



Name:

Interrupt Status Registers



Size:

64 bits



Address offset:



StatusTfr – 0x2e8



StatusBlock – 0x2f0



StatusSrcTran – 0x2f8



StatusDstTran – 0x300



StatusErr – 0x308



Read/write access:

read

All interrupt events from all channels are stored in these Interrupt Status registers after masking: StatusBlock, StatusDstTran, StatusErr,
StatusSrcTran, and StatusTfr. Each Interrupt Status register has a bit allocated per channel; for example, StatusTfr[2] is the Channel 2 status
transfer complete interrupt. The contents of these registers are used to generate the interrupt signals (int or int_n bus, depending on interrupt
polarity) leaving the DMAC.

Bit

Name

Access

Reset

Description

63:DMAH_NUM_CHANNELS

RSVD

N/A

0x0

Reserved

DMAH_NUM_CHANNELS-1:0

STATUS

R

0x0

Interrupt status.

9.3.2.3.3

MaskBlock, MaskDstTran, MaskErr, MaskSrcTran, MaskTfr



Name:

Interrupt Mask Registers

Realtek confidential files

The document authorized to

SZ99iot

2019-05-15 10:08:03

«
...
149
150
151
152
153
...
»

Содержание Ameba-D RTL872 D Series















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ameba-D RTL872 D Series

Бренд: Yamaha Страницы: 497

Бренд: Supermicro Страницы: 2

Бренд: Aaeon Страницы: 120

SKR E3 DIP V1.0

Бренд: BIGTREETECH Страницы: 10

B560M DS3H PLUS

Бренд: Gigabyte Страницы: 42

Бренд: DFI Страницы: 120

Бренд: Gigabyte Страницы: 18

Бренд: Variscite Страницы: 2

Бренд: IBASE Technology Страницы: 72

Бренд: Avalue Technology Страницы: 116

Бренд: Digilent Страницы: 17

Бренд: Microsemi Страницы: 22

COMe Ref.Carrier T6

Бренд: Kontron Страницы: 41

Бренд: Biostar Страницы: 210

Бренд: Intel Страницы: 29

Бренд: J&W Страницы: 42

Бренд: EVGA Страницы: 40

Z77A-GD65 GAMING series

Бренд: MSI Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды