Pentair SunTouch Скачать руководство пользователя страница 57

Страница: 57 / 92

SunTouch

Control System Installation and User’s Guide

SunTouch

Control System Power Center High Voltage

Connections

WARNING - BEFORE OPENING THE FRONT PANEL OF THE SUNTOUCH

CONTROL SYSTEM

POWER CENTER TO ACCESS THE HIGH VOLTAGE COMPARTMENT AND LOW VOLTAGE RACEWAY

SWITCH THE MAIN POWER OFF INTO THE HOME AT THE MAIN CIRCUIT BREAKER BOX, AND SWITCH

OFF THE MAIN POWER TO THE SUNTOUCH CONTROL SYSTEM POWER CENTER.

SunTouch

Control System Power Center Location

Before installing the SunTouch

Control System Power Center read the following guidelines:

• Switch OFF AC power at the main circuit breaker panel, located at the house before high and low

voltage connection to the SunTouch Control System Power Center.

• AC power for the SunTouch Control System Power Center must be provided from the main circuit

breaker panel located at the house.

• All electrical equipment must be installed at least five (5) feet from pool and/or spa, and comply

with all national, state, and local codes.

• Install the SunTouch Control System Power Center no less than five (5) feet from pool or spa near to

the pumps, heater, valves, and sensors. Mount the Power Center outside or inside a pool equipment

house or other enclosure.

• Before choosing the final location for the SunTouch Control System Power Center, consider the

length of the wires and valve wires that have to be connected to the enclosure. Make sure to consider

cable lengths for the sensors to the SunTouch Power Center location. The air temperature sensor

cable is 3 feet long and the water temperature sensor is 20 feet long.

• Mount the SunTouch Control System Power Center on a flat vertical surface or wall so that the

conduit knockouts are located at the bottom of the enclosure. Upper and lower brackets are provided

to mount the Power Center to a vertical surface.

• DO NOT mount the SunTouch Control System Power Center horizontally. Water can enter the

conduit knockouts and cause damage to the system and an electrical shock hazard.

• Consider the SunTouch Control System Power Center location when routing the conduit carrying

the AC power to the SunTouch Power Center, and the conduit that will be run to the high voltage

equipment.

• All the SunTouch Control System high voltage double pole relays and are rated at 3HP/30A at 240

VAC (1˝ HP/30A at 120 VAC).

• Install the SunTouch Control System Power Center so that drainage is provided for all electrical

components.

• Motors should have built-in thermal protection.

• Allow for unobstructed access to the front of the SunTouch Control System Power Center for the

owner or service personnel.

• The SunTouch Control System Power Center provides grounding screw terminals for grounding all

equipment. All equipment including the SunTouch Control System Power Center must be bonded to

earth ground.

Содержание SunTouch





























































































Результаты поиска

Содержание SunTouch

Отзывы:

Похожие инструкции для SunTouch

Бренды по названию

Популярные бренды

Pentair SunTouch, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SunTouch

Отзывы:

Похожие инструкции для SunTouch

Бренды по названию

Популярные бренды