28
SunTouch
®
Control System Installation and User’s Guide
Settings Menu (11/14): QuickTouch
®
(QT4) Wireless Remote
The QuickTouch
®
(QT4) Wireless Remote provides switching of up to four circuits. For example, you can use
the QT4 Wireless Remote to activate the spa circulation, and for operating three auxiliary pieces of equipment
(such as heat enabled, lights, jet pump, heat boost, air blower, waterfall, etc.).
Each of the four functions on the QT4 Wireless Remote has an on and an off button. To switch a circuit on or
off, press and hold the appropriate button for at least a full second.
The QT4 Wireless Remote4 buttons can be assigned to any available circuit. However, the QT4 has the
following preset circuits assigned to the four buttons:
• The SPA button activates the spa circuit (same as the Up button on the SunTouch Control System
Control Panel.)
• A button activates the AUX 1 circuit.
• B button activates the AUX 2 circuit.
• C button activates the AUX 3 circuit (see page 26 for AUX 3 assignment information).
Assign QuickTouch (QT4) buttons
To assign circuits to the QuickTouch Wireless Remote buttons:
Menu button:
Select the
QuickTouch 11/14
menu.
Right button:
Assign the
QuickTouch SPA button
to a circuit.
Up/Down buttons:
Choose a circuit to assign to the SPA button. The circuit
selections are: None, Spa, Pool, AUX 1, AUX 2, AUX 3, FEATURE 1 - 4, HEAT
BOOST, HEAT ENABLED. Selecting “None” does not assign a circuit.
Note: The “Heat Boost” feature will switch on the heater for seven minutes to
increase the spa water temperature. Each time the spa Heat Boost button is pressed,
the temperature will increase about 1
°
F. The temperature will not go beyond the 104
°
F (40° C) limit.
Right button:
Assign button A to a circuit 1. Use the Up/Down buttons to select a
circuit for button A. Repeat the process for Buttons B (AUX 2 circuit 2) and C (AUX
circuit 3).
Left button:
Press the Left button to return to the main status screen.
QuickTouch
2 - [POOL ]
QuickTouch
3 - [AUX1 ]
Main Menu 11/14
QuickTouch
QuickTouch
1 - [HEAT BOOST]
QuickTouch
SPA - [SPA ]
Pump Menu (12/14)
From the Pump menu you can setup SunTouch
®
Control System to operate a single-speed or two speed
pump, or assign up to eight speeds and circuits for the IntelliFlo
®
VS and VF Pumps. The SunTouch
®
control
system can be setup to operate either one IntelliFlo VS or one IntelliFlo VF pump. The SunTouch
®
Control
System communicates with the IntelliFlo VS and the IntelliFlo VF pump via a two-wire RS-485 cable. For
information about connecting the RS-485 communication cable from SunTouch control system Power Center
to the IntelliFlo pump, refer to the IntelliFlo VS Pump Installation and User’s Guide (P/N 357269).
SINGLE SPEED FILTER PUMP
For a single-speed pump there are no assigned pump circuits. The pool filter pump schedule program
determines when the pump is switched on and off. If the heat source is enabled in the “Heat” menu (see page
14), when the pool or spa circuit is activated the selected heat source is also enabled. The default time before
the filter pump will switch off is 12 hours. If the pool/spa circuit is switched off and the heater is operating,
only the heater will turn off, then the filter pump will automatically switch off after 10 minutes to allow the
heater to cool down. Pentair Aquatic Systems heaters do not require a cool down time. To override the “heater
cool-down,” press the Filter Pump button again to switch off the pump.