background image

8

 

SunTouch

®

 Control System Installation and User’s Guide 

Solar Only Menus 

(Continued)

Heat Start and Stop Temp Differentials: 

 Use this feature to adjust the start and stop

temperature deferential settings to start and stop solar water heating. 

Solar Freeze protection: 

 Use this feature to enable freeze protection for the solar equipment.  

Menu button: 

The Set Water Temp setting is displayed. 

Right button: 

Press the button until the Solar Freeze setting is displayed.

 

Up/Down button: 

Select 

Yes

 to enable solar freeze protection or 

No

 to disable freeze 

protection. If 

Yes 

is selected, the circuit will switch on if the air temperature drops to 

36° F (2° C). This feature is used to protect the system plumbing from being damaged 

during freezing conditions. 

Note: When freezing conditions are detected by the air 

sensor, the filter pump will be switched on and water will circulate continuously 

through the system.

 

Left button: 

Press the Left button to return to the main status screen.

Cleaner Freeze protection: 

Use this feature to enable freeze protection for cleaner equipment.  

Menu button: 

The Set Water Temp setting is displayed. 

Right button: 

Press the button until the Cleaner Freeze setting is displayed.

 

Up/Down button: 

Select 

Yes

 to enable cleaner freeze protection or 

No

 to disable 

freeze protection. If 

Yes

 is selected, the circuit will switch on if the air temperature 

drops to 36° F (2° C). This feature is used to protect the cleaner equipment from 

being damaged during freezing conditions. 

Note: When freezing conditions are 

detected by the air sensor, the filter pump will be switched on and water will circulate 

continuously through the system.

 

Left button: 

Press the Left button to return to the main status screen.

 

 

 

 

 

 

Menu button: 

The Set Water Temp setting is displayed.

 

Right button: 

Press the button until the Air Sensor is displayed.

 

Up/Down buttons: 

Select 

Yes

 to enable the sensor. Select 

No

 to disable the    

sensor (and not display the air temperature on the main status screen). 

Left button: 

Press the Left button to return to the main status screen.

 

Heat  Start Temp 
Temp Diff:    6°

Solar Freeze
Enabled:   Yes

Cleaner Freeze
Enabled:   Yes

Heat  Stop Temp 
Temp Diff:    3°

Air Sensor
Enabled:   Yes

Note: Air Sensor (freeze protection requirement):  Freeze protection for solar systems (“Solar Only” mode) requires 

an optional ambient air temperature sensor and relay for the filter pump and or cleaner pump override. See page 81 

for Time clock pump override information. The air sensor must be enabled to display the current air temperature on 
the main status screen. The optional air temperature sensor is used to protect the system plumbing and equipment 
against freeze damage. For information about freeze protection for circuits, valves and auxiliaries, see page 9. To 
enable or disable the air sensor:

Note: The solar roof sensor must be 6° higher than the water temperature. The pump must be ON for a few minutes 
for operation. When the roof sensor and the water temperature are within 3°, solar heat will switch off. This 
differential setting is adjustable in the “Stop Temp Diff” setting. Adjusting the differential will effect the performance 
of your solar system. See you solar professional for the optimum setting.

Press Menu button 

the Solar Status setting is displayed. Press 

Right button 

until the “Start 

Temperature Deferential” setting is displayed. Press 

Up/Down button 

to adjust “Heat Start 

Temp” differential setting (default setting 6°). Press 

Right button 

to move to the “Heat 

Stop Temp” setting. Press 

Up/Down button 

to adjust “Heat Stop Temp” differential setting 

(default is 3°). This setting sets how close to the target set point temperature to switch off 

solar heat. Press 

Left button 

to return to the main status screen.

Cool  Start Temp 
Temp Diff:    6°

Cool  Stop Tempf 
Temp Diff:    3°

Cooling (Enabled) and Start and Stop Temp Differentials: 

 

When “Cooling” is enabled, water will circulate through the 

system to lower the temperature during the night hours. Adjust 

the “Cool Start and Stop Temp differential temperatures settings. 

Содержание SunTouch





























































































Отзывы: