Paradyne COMSPHERE 3610 Скачать руководство пользователя страница 191 | Manualshive

Страница: 191 / 310

background image

B-1

3610-A2-GB91-90

July 1999

Configuration Worksheets

Overview

B-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Instructions

B-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Overview

This appendix contains a complete set of Configuration

Worksheets used for the 3600 Series DSU and its options.
These sets include the following:

•

Configuration Worksheet for TDM Mode, which is
used for the DSU with TDM. This worksheet
includes the DBM and SNA Diagnostic Interface
options, as well, so no other worksheet is required.

•

Configuration Worksheet for MCMP Mode, which
is used for the DSU with MCMP. This worksheet
includes the DBM and SNA Diagnostic Interface
options, as well, so no other worksheet is required.

•

Configuration Worksheet for Bridge Mode, which
is used for the DSU with TDM or MCMP. This
worksheet includes the SNA Diagnostic Interface
option, as well, so no other worksheet is required.

•

Configuration Worksheet for Basic Mode, which is
used for the DSU without options, or the DSU with
the DBM and/or SNA Diagnostic Interface options.

•

Configuration Worksheet for Basic (DBM-V,
DBM-S, or DBM-D) Mode, which is used for the
DBM-V, DBM-S, or DBM-D that is connected to
the TDM or MCMP operating in Bridge mode.

A Configuration Worksheet summarizes the DSU’s

option sets, configuration options, and configuration
option values. The Configuration Option Tables in

Chapter 6

provide an explanation for each configuration

option within each option set based upon the DSU’s mode
of operation.

Refer to the

Configuration Options

section, Chapter 6,

when configuring the unit, or when more detailed
configuration information is needed.

Instructions

Configuration Worksheets can be used for reference, or

they can be used to record changes made to the DSU’s
configuration options or to record the configurations
saved to the Usr1, Usr2, or Usr3 areas of the DSU.

Make a copy of the Configuration Worksheet that is

provided. Complete the information at the top of each
worksheet first. If you have a Model 3610 (standalone)
DSU, enter your site in the location field; if you have a
Model 3611 (carrier-mounted) DSU, enter the DSU’s
carrier and slot location. (If recording Model 3611 DSU
configurations, make a copy for each DSU.)

Record the configuration or changes by circling the

appropriate configuration setting, either all of the
configuration options or all those that have been changed
from their factory-loaded default values. Circle the
appropriate hardware strap settings, as well.

B

«
...
189
190
191
192
193
...
»

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

Бренд: Campbell Страницы: 4

Бренд: ADTRAN Страницы: 57

ComStream DMD2401

Бренд: Radyne Страницы: 199

COMSPHERE 3000 Series

Бренд: Paradyne Страницы: 131

Бренд: Linksys Страницы: 12

Бренд: CalAmp Страницы: 62

Бренд: ICP DAS USA Страницы: 3

NetLink 1082/144/I

Бренд: Patton electronics Страницы: 28

Бренд: SafeNet Страницы: 54

Бренд: Maxon Страницы: 100

Бренд: LOVATO ELECTRIC Страницы: 8

CellPipe IAD 4A

Бренд: Lucent Technologies Страницы: 28

Donatello Memory ISDN Modem

Бренд: Digicom Страницы: 1

Бренд: Digi Страницы: 3

Connect WAN 3G IA

Бренд: Digi Страницы: 1

Бренд: Digi Страницы: 866

Бренд: BT Страницы: 20

Бренд: 3onedata Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды