Paradyne COMSPHERE 3610 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 310

background image

COMSPHERE 3600 Series Data Service Units

4-30

July 1999

3610-A2-GB91-90

When Opts is selected, the following appears:

F1

Load from:
Activ

Remt

Usr1

F2

F3

Usr2

Usr3

FacC

FacT

FacB

The selections on this menu are configuration option

sets or libraries of configuration options stored in the
DSU’s memory. Table 4-10 lists the Load from option
selections and their source.

Table 4-10

Default Configuration Option Sets

Menu

Selection

Source Of

Configuration Options

Activ

The addressed DSUs currently
active options.

Remt

Options can be retrieved from a
selected tributary DSU; these
may be from the tributary’s Activ,
Usr1, Usr2, or Usr3 set.

The selected option set can then
be displayed, edited, and saved
back to the same tributary,
another tributary, or the control
DSU.

Usr1

User-defined option sets.

Usr2

User-defined option sets.

Usr3

1

User-defined option sets, and
factory default settings for a
DBM-V, DBM-S, or DBM-D.

FacC

Factory default settings for a
control DSU.

FacT

Factory default settings for a
tributary DSU.

FacB

Factory default settings for a
central-site bridge.

1

If configuring a DBM-V, DBM-S, or DBM-D, do
not SAVE to Usr3.

If you select Activ, Usr1, Usr2, Usr3, FacC, or FacT

from the Load from menu, a complete set of
configuration option values is loaded into a working
buffer.

Usr1, Usr2, and Usr3 are storage areas for user-defined

configuration option sets. This feature allows the rapid
loading of an entire configuration option set, saving the
time required to change each individual configuration
option.

If you select Remt from the Load from menu, an

address is required. The remote ADp address selections
range from 1 to 255 (1 to 80 for DPII protocol). For a list
of allowable addresses, see the

Addressing

section in

Chapter 1.

When the configuration options are saved to a remote

device, they can be saved to all the remote devices by
selecting 192 (the Broadcast Address). If 192 is selected,
the configuration options changed are broadcast to the
entire network after the configuration options are saved.

When downloading configuration options, it is

recommended that the control and tributary DSUs have
the same firmware version, or that the control has the
highest version.

After you enter the tributary address, press F3 to

display the following submenu for a remote device:

F1

Load from:

Activ

Usr1

Usr2

F2

F3

Usr3

Each of the selections listed in

Table 4-10

(except for

Remt) loads a complete set of configuration options into a
working buffer in the local DSU. Once the values are
loaded into the DSU, the Edit/Save submenu appears.

F1

Edit/Save:
SAVE DSU

Diag

F2

F3

DBM

Gen

Bckup

From this point, you will be editing and saving

configuration options. Refer to

Chapter 6

to learn how to

configure your unit.

«
...
108
109
110
111
112
...
»

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

Бренд: Javad Страницы: 7

ComStream DMD2401

Бренд: Radyne Страницы: 199

Бренд: ADC Страницы: 7

Бренд: Patton electronics Страницы: 17

Mblaze Ultra Wi-Fi

Бренд: Zte Страницы: 73

Бренд: Ebyte Страницы: 15

Бренд: Ebyte Страницы: 20

Бренд: Ebyte Страницы: 34

Бренд: Ebyte Страницы: 35

Бренд: Ebyte Страницы: 35

Бренд: Cradlepoint Страницы: 137

Бренд: C-motech Страницы: 15

Бренд: Zte Страницы: 9

Бренд: Dataradio Страницы: 73

Бренд: Campbell Страницы: 12

Бренд: netsys Страницы: 63

Бренд: Acer Страницы: 136

Бренд: Acer Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды