Paradyne COMSPHERE 3610 Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 310

background image

Configuration Options

6-19

3610-A2-GB91-90

July 1999

Table 6-5

(3 of 6)

DBM Configuration Options

Single Rate: Yes
Next Yes No Prev

Single Rate.

1, 2

Determines whether the DBM will adjust its rate to resolve a rate mismatch with a remote

DBM or modem with the following limitations.

If Rate(Kbps) is set to 2.4, the DBM can only talk to a 2.4 kbps modem, regardless of the Single Rate

setting. (Will only train at 2.4 kbps.)

Yes

—

The DBM operates only at the rate for which it is configured.

No

—

The DBM will adjust its rate downward to correct a mismatch.

AutoAnswer: Enab
Next Enab Disab Prev

Automatic Answer. Controls whether the DBM answers incoming calls.

Enab

—

DBM answers incoming calls.

Disab

—

DBM does not answer incoming calls.

TxElasStor:Disab
Next Enab Disab Prev

Transmit Elastic Store.

3

The Transmit Elastic Store hardware consists of a receive buffer on the DSU’s

transmit data (TXD) lead. Serial data from the extended circuit is clocked into the DSU’s elastic store using a
clock (on EIA-232-D Pin 24 or V.35 Pins U and W on Port 1). The DSU uses its own system timing to clock
data out of the buffer. The Transmit Elastic Store buffer is reset upon power-up, overflow, or after the RTS
lead makes an Off-to-ON transition.

Enab

—

Enable this configuration option if you have an extended network.

Disab

—

Disable this configuration option if you do not have an extended network.

RxElasStor:Disab
Next Enab Disab Prev

Receive Elastic Store. The Receive Elastic Store hardware consists of a buffer on the DSU’s receive data
(RXD) lead. Serial data from the extended circuit is clocked out of the DSU elastic store using a clock (on
EIA-232-D Pin 24 or V.35 Pins U and W on Port 1). This configuration option is only valid for a single-port
DBM with disruptive diagnostics.

Enab

—

Enable this configuration option if you have an extended network.

Disab

—

Disable this configuration option if you do not have an extended network.

1

Does not appear for Switched 56 DBM.

2

DBMs with firmware versions less than 2.0, with Rate(Kbps) set to 12.0, will also train at 9.6 kbps or
4.8 kbps, even when Single Rate is set to Yes.

3

In TDM, MCMP or Bridge mode, the DBM’s Transmit Elastic Store setting is ignored; instead, this
configuration option is selected on a per-port basis in the MUX submenu.

«
...
145
146
147
148
149
...
»

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

Zlinx Xtreme ZXT9-RM

Бренд: B&B Electronics Страницы: 163

Бренд: u-blox Страницы: 79

ComStream DMD2401

Бренд: Radyne Страницы: 199

Бренд: NAPCO Страницы: 16

Бренд: Elcon Страницы: 24

Бренд: StarHub Страницы: 10

RFI 150-W-D-DD-H-1

Бренд: RF Innovations Страницы: 30

Бренд: Konig Страницы: 5

Бренд: FiberHome Страницы: 78

Бренд: Zte Страницы: 2

Бренд: Four-Faith Страницы: 22

Бренд: Technicolor Страницы: 29

Бренд: CSL Страницы: 16

Бренд: Ubee Страницы: 74

FRITZ!Box 6660 Cable

Бренд: Fritz! Страницы: 281

Бренд: RCA Страницы: 35

Бренд: Hughes Network Страницы: 56

Бренд: AmazonBasics Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды