Paradyne COMSPHERE 3610 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 310

background image

COMSPHERE 3600 Series Data Service Units

1-24

July 1999

3610-A2-GB91-90

Point-to-Point Configuration

To set up aggregate switching for a single-port,

point-to-point configuration, enable the following
configuration options:

•

DSU Configuration Options

(Table 6-5):

– AggrSwitch (Aggregate Switch) must be

enabled.

– AgSw Timing (Aggregate Switch Timing) must

be set to the appropriate timing source to be used
during dial backup.

•

DBM Configuration Options

(Table 6-9); for the

DBM, DBM-V, DBM-S, DBM-D, or other external
dial backup unit (DBU) connected to the switched
aggregate port:

– Rate(Kbps) (DBM Rate) must be set to the same

rate as the DSU rate.

– Diag Type (Diagnostic Type – Diagnostic DBM

Options) must be set to None or Disr.

To establish aggregate switching dial backup from the

DCP, run backup from the control DSU and command the
DBM-V, DBM-S, or DBM-D to dial and go into Dial
mode. From the 6800 Series NMS, use the Standby
Facility (sf) and Dial commands. The 6700 Series NMS
software provides a Commands pull-down window to
access Standby Facility. Aggregate switching can also be

controlled automatically, enabling the Answer External
Backup (AnswExtBU) configuration option.

Refer to Figure 1-6 for a sample aggregate switched

backup for a point-to-point configuration. The control
DSU is configured so that AggrSwitch is enabled and
AgSw Timing is set to Aggr. In this example, the DSU
takes its timing from the Switched 56 DBM when in Dial
Backup mode.

Multipoint Configuration

To set up aggregate switching for a multipoint

configuration, enable the following configuration options:

•

DSU Configuration Options

(Table 6-5):

– AggrSwitch (Aggregate Switch) must be

enabled.

– AgSw Timing (Aggregate Switch Timing) must

be set to the appropriate timing source to be used
during dial backup.

•

DBM-V, DBM-S, DBM-D, or other external

DBM

Configuration Options

(Table 6-9):

– Rate(Kbps) (DBM Rate) must be set to the same

rate as the DSU rate (no rate adaption).

– Diag Type (Diagnostic Type – Diagnostic DBM

Options) must be set to None or Disr.

Figure 1-6. Aggregate Switched Backup for a Point-to-Point Configuration

«
...
38
39
40
41
42
...
»

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

Бренд: Datum Systems Страницы: 13

Бренд: Boca Страницы: 52

Бренд: ActionTec Страницы: 2

Бренд: NAPCO Страницы: 16

Бренд: Zte Страницы: 16

Бренд: MikroTik Страницы: 3

Бренд: GridConnect Страницы: 17

Бренд: Wellink Страницы: 32

Бренд: D-Link Страницы: 16

SURFboard SBG6950AC2

Бренд: CommScope Страницы: 64

Impact IQ 3C882

Бренд: 3Com Страницы: 114

Бренд: Zhone Страницы: 2

Бренд: Campbell Страницы: 28

Бренд: Kamstrup Страницы: 12

Бренд: Radyne Страницы: 237

SMC-GPRS Series

Бренд: CalAmp Страницы: 84

Бренд: Cambium Networks Страницы: 158

Бренд: Patton electronics Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды