Paradyne COMSPHERE 3610 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 310

background image

COMSPHERE 3600 Series Data Service Units

6-10

July 1999

3610-A2-GB91-90

Table 6-2

(1 of 3)

Diagnostic DSU Configuration Options

Diag Type: Disr
Next NonD Disr Mixed None Prev

Diagnostic Type. Defines the diagnostic interaction between the control and tributary DSUs. It must be set
consistently for all DSUs on the same circuit.

NOTE: If the DSU Rate(Kbps) is set to 64CC, the DSU defaults to 3600e and no other configuration options

will appear for this option set.

NonD

—

Nondisruptive Diagnostics. An in-band secondary channel transport is derived to carry
diagnostics data between the control and the tributary DSUs. Nondisruptive diagnostics are
unavailable using the DMC protocol.

Disr

—

Disruptive Diagnostics. The same (primary) channel that carries user-transmitted data between
the control and the tributary DSUs also carries diagnostic data. This mode should be selected
for compatibility with earlier releases that use session-disruptive diagnostics.

Mixed —

This mode supports nondisruptive health and status updates. User-initiated commands are
sent disruptively. Mixed is unavailable using the DMC protocol and is only selected in
single-port multipoint configurations.

None

—

No diagnostic communications with remote devices; only local diagnostics are allowed.

«
...
136
137
138
139
140
...
»

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

Бренд: Data-Linc Group Страницы: 4

Бренд: M/A-Com Страницы: 22

Бренд: T-Mobile Страницы: 10

Бренд: WePresent Страницы: 71

Бренд: Siemens Страницы: 25

Бренд: Siemens Страницы: 48

Бренд: Siemens Страницы: 79

Бренд: Arris Страницы: 1

819-1XRT SERIES

Бренд: Cal Amp Страницы: 48

Бренд: Enfora Страницы: 23

Бренд: FAAC Страницы: 20

OfficeConnect 3C886A

Бренд: 3Com Страницы: 24

Бренд: Manta Страницы: 6

Бренд: I/O Страницы: 10

Бренд: Hughes Network Systems Страницы: 53

Бренд: Aritech Страницы: 10

Бренд: Maestro Страницы: 29

Бренд: LandCell Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды