Paradyne COMSPHERE 3610 Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 310

background image

COMSPHERE 3600 Series Data Service Units

6-34

July 1999

3610-A2-GB91-90

Table 6-9

(1 of 3)

TDM Setup (MUX Funct: TDM) Configuration Options

MUX Funct: TDM
Next TDM MCMP CBrdg EBrdg None Prev

TDM/MCMP Circuit Card Function with TDM mode selected. Selects the mode of operation for the TDM or
MCMP circuit card.

TDM

—

Configures for TDM mode for a point-to-point multiplexing or digital-sharing configuration.

MCMP —

Configures for MCMP mode for multichannel multipoint operation and digital-sharing
configuration (only displayed for an MCMP circuit card).

CBrdg

1

—

Configures for Bridge mode for a central-site bridge configuration.

EBrdg

1

—

Configures for Bridge mode for a extended bridge configuration.

None

—

Configures for Basic mode, which bypasses the TDM or MCMP circuit card.

Share DevA: Disab
Next Enab Disab Prev

Sharing Device A.

2

Enabling this configuration option allows you to create one of two digital-sharing groups.

The following rules apply:

•

All ports in a group must have the same port speed.

•

All ports must be adjacent.

•

A digital-sharing group can have from 2 to 6 ports (only 2 ports when a 2-port TDM/Flex is installed).

Enab

—

Enables the digital-sharing feature.

Disab

—

Disables the digital-sharing feature.

Lowest Port #: 1
Next 1 2 3 4 5 Prev

Lowest Port Number. Allows selection of the lowest port number to be included in the digital-sharing group.
This configuration option is displayed only if Sharing Device A is enabled.

1 to 5

—

Selects the lowest port number. This configuration option does not appear when a 2-port
TDM/Flex is installed.

# Ports in Gp: 2
Next 2 3 4 5 6 Prev

Number of Ports in Group. Allows selection of the total number of ports to be included in the digital-sharing
group. This configuration option is displayed only if Sharing Device A is enabled.

Enabling Sharing Device A and accepting the defaults for configuration options Lowest Port Number and
Number of Ports in Group places Ports 1 and 2 in the digital-sharing group.

Individual ports in a digital-sharing group can be configured for streaming terminal. If streaming terminal
detection is enabled on a port and RTS for that port is ON longer than the value selected for that port, the
port’s leads are clamped until RTS is turned Off.

2 to 6

—

Selects the number of ports. This configuration option does not appear when a 2-port
TDM/Flex is installed.

1

If a DBM is installed, it must be disabled when the DSU is configured for CBrdg or EBrdg.

2

For an LPDA-2 configuration, only Sharing Device A can be used to create a digital-sharing group.

«
...
160
161
162
163
164
...
»

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

Ripwave 2300E/U

Бренд: Navini Networks Страницы: 48

MultiModem MT2834ZDX Series

Бренд: Multitech Страницы: 8

Бренд: Data-Linc Group Страницы: 31

Бренд: MikroTik Страницы: 4

Бренд: Zte Страницы: 22

Бренд: AVM Страницы: 51

Бренд: QTech Страницы: 8

Бренд: Spectrum Страницы: 7

Бренд: Spectrum Страницы: 6

Бренд: Hercules Страницы: 6

Бренд: C-motech Страницы: 19

Бренд: B&B Electronics Страницы: 2

Бренд: CTC Union Страницы: 40

Бренд: CTC Union Страницы: 68

Бренд: PowerTraveller Страницы: 2

Бренд: Telstra Страницы: 22

Бренд: NAL RESEARCH CORPORATION Страницы: 114

Бренд: Orcon Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды