Paradyne COMSPHERE 3610 Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 310

background image

COMSPHERE 3600 Series Data Service Units

4-4

July 1999

3610-A2-GB91-90

Table 4-1

3600 Series DSU Status Indicators

Label

Color

Description

OK

Green

Health and status indicator. The DSU’s operation is normal. (The DSU
has not detected any alarm listed in the next section labeled Alrm.)

This indicator flashes two times per second if a message is present.

Alrm

Red

Health and status indicator. An alarm in the local or remote DSU. For the
DSU with TDM or MCMP,

1

the alarm may be in the communications

path between the DSU and TDM or MCMP circuit card.

The following alarms at the local or remote DSU cause the Alrm status
indicator on the affected DSU to light: Configuration Corrupt, Device
Alarm, Dial Tone Test Failure, DTE Alarm, Facility Alarm, MUX Failure,
No Response, Redundant Power Alarm, Streaming Terminal,
Subnetwork Alarm, and Out-of-Frame Threshold.

Test

Yellow

Active device (DSU or DBM) is either performing a test, or other DSUs or
DBMs are in Test mode. For a DSU with TDM or MCMP, test activity may
be in the TDM or MCMP circuit card.

2,3

Dial

Yellow

DBM active:

Rapid flashing: Call setup in progress
Slow flashing: Call established but in Standby mode
Steady ON: Backup call established and active

TXD, RXD, RTS,
CTS, DSR, DTR,
LSD

4

Green

Internal lead states at DSU/DTE interface

(circuit designations):

Control circuit active,

or

Data circuit SPACEing.

For the DSU with TDM or MCMP, the circuit external lead states for any
of the TDM or MCMP ports can be selected from the DCP via the Control
Branch.

For a 3611 Series DSU with TDM or MCMP, the port LED illuminated on
the TDM or MCMP faceplate indicates the monitored port. For
Model 3610 DSUs, the monitored port is displayed on the DCP’s LED
display.

Front Panel
(Model 3611 only)

Yellow

DSU is currently selected by the SDCP (

the SDCP addresses one DSU

at a time).

For Model 3611 DSU with TDM or MCMP, the TDM or MCMP circuit card
is also selected (

the TDM or MCMP circuit card has the same address as

its associated DSU).

1

Health and status for the TDM or MCMP is integrated into the Health and Status report for the DSU. For an
alarm in the DSU with TDM or MCMP, this report indicates whether the TDM/MCMP or DSU is at alarm.

2

Any test involving the TDM or MCMP also involves the DSU, and the test is integrated into the DSU’s
Health and Status report.

3

The DSU or DBM is automatically put into Test mode when a remote DSU or DBM is performing a
disruptive test (e.g., a Local Loopback at the control DSU — select LL). A DSU or DBM in Test mode has
its DTE interface turned Off.

4

When the TDM or MCMP option is installed, DTR will always appear as ON for Port 1. Refer to the DTE
Status display on the DCP to determine the state of the DTR lead.

«
...
82
83
84
85
86
...
»

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

Бренд: Datakom Страницы: 23

Бренд: Intercel Страницы: 7

Бренд: Commander Страницы: 5

Бренд: Ubee Страницы: 22

Бренд: AirLive Страницы: 77

Бренд: Infiniteq Страницы: 11

Бренд: Palm Страницы: 20

Бренд: Blonder tongue Страницы: 20

Бренд: Fon Страницы: 79

Бренд: Cradlepoint Страницы: 2

Бренд: C-motech Страницы: 15

Бренд: Franklin Страницы: 38

Бренд: Tecnet Страницы: 2

Бренд: CTC Union Страницы: 40

Бренд: CTC Union Страницы: 68

epConnected Asset

Бренд: Embedded Planet Страницы: 38

EZ Connect SMC2642W

Бренд: SMC Networks Страницы: 22

Бренд: ICP DAS USA Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды