manualshive.com logo in svg

Paradyne COMSPHERE 3610, Руководство оператора

Программный инсталляционный руководство для Paradyne COMSPHERE 3610 теперь доступен для загрузки совершенно бесплатно с manualshive.com. Этот manual поможет вам правильно установить необходимое software на ваше устройство, обеспечивая его оптимальную работу. Необходимая информация теперь всегда под рукой!

Поделиться
Скачать
background image

Model 3611 Installation

3-7

3610-A2-GB91-90

July 1999

Power-Up Routine

When power is applied, the DSU:

•

Determines what options (DBM, MUX-TDM or
MCMP) are installed, if any.

•

Runs a Device Test on itself and each of the
installed options.

During the tests, all indicators on the DCP light
briefly and the message Power-Up Tests appears
on the liquid crystal display (LCD).

•

Displays the results of each test momentarily as
Pass, Fail, or Abrt. (Abrt indicates that the Device
Test was aborted because a network loopback was
in progress during the power-up procedure.) These
tests take about 20 seconds to complete.

If the DSU fails the power-up test:

"

Procedure

1. Confirm the hardware options that are installed, if

any.

2. Go to the Configuration (Confg) branch, load and

save a factory-set configuration (FacC or FacT).

3. Return to the Test branch.

4. Re-execute the Device Test. If the test passes,

continue with this procedure.

If the test fails again, contact your service
representative for instructions on how to return the
DSU.

Since the DSU is not connected to the network,
the red Alrm indicator is lit, and the LCD displays
No Signal, indicating a facility alarm. The LCD
displays Health and Status information as
described in the 

Status Branch

 section of

Chapter 4.

Installing a Modular 3611 DSU

The initial installation procedure for the Modular 3611

DSU requires the installation of a rear connector plate
onto the rear of the COMSPHERE 3000 Series Carrier.
After the initial installation, the DSU can be installed and
removed from the front of the carrier without first
disconnecting the DTE cables at the rear of the carrier.
This section provides the initial installation procedure and
the procedure for subsequent installations.

To install a DSU and rear connector plate for the first

time:

"

Procedure

1. At the rear of the carrier, set the tab on the rear

connector plate into one of the slotted grooves on
the carrier’s backplane. Loosely fasten the screws.
Make sure the rear connector plate uses the same
slot position intended for the DSU.

2. Loosely fasten the screw attached to the rear

connector plate, allowing for slight adjustment
that may be needed when installing the DSU.

3. Change any default hardware strap settings that

may be required before installing the DSU in the
carrier. For example, straps that determine:

•

Permissive (default) or programmable V.32
DBM interface switch.

•

Enabled (default) or disabled Test Mode
Indication jumper.

4. Using a Phillips screwdriver, loosen the screw

holding the circuit pack lock and rotate the lock to
the open position (

Figure 3-3

). Open the latch.

5. At the front of the carrier, hold the DSU vertically

with the latch on its faceplate in the open position.
Then, insert the circuit card into the top and
bottom circuit card guides for the slot that
contains the rear connector plate.

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

FUTABA FDP03TJ010 Instruction Manual preview
FDP03TJ010
Бренд: FUTABA Страницы: 70
Patton electronics NetLink 1082/144 User Manual preview
NetLink 1082/144
Бренд: Patton electronics Страницы: 32
Dantel B18-04649-01 Installation & Operation Manual preview
B18-04649-01
Бренд: Dantel Страницы: 14
Tandy DCM-6 Operation Manual preview
DCM-6
Бренд: Tandy Страницы: 16
KYL 668H User Manual preview
668H
Бренд: KYL Страницы: 6
Kathrein EXI 01 Manual preview
EXI 01
Бренд: Kathrein Страницы: 16
Hama FlashPen USB 2.0 Manual preview
FlashPen USB 2.0
Бренд: Hama Страницы: 2
ComBlock COM-1503 Manual preview
COM-1503
Бренд: ComBlock Страницы: 22
Palm Handbook Handbook preview
Handbook
Бренд: Palm Страницы: 20
Raymar 2.4 MIU/PowerPort Series Installation & Operation Manual preview
2.4 MIU/PowerPort Series
Бренд: Raymar Страницы: 30
3Com HomeConnect 3CR29223 Installation Manual preview
HomeConnect 3CR29223
Бренд: 3Com Страницы: 1
3Com Impact External ISDN Modem Quick Start Instructions preview
Impact External ISDN Modem
Бренд: 3Com Страницы: 6
Coster GSM 822 Manual preview
GSM 822
Бренд: Coster Страницы: 4
SMC Networks EZ Connect SMC7003-USB User Manual preview
EZ Connect SMC7003-USB
Бренд: SMC Networks Страницы: 70
Ubee DDW365 User Manual preview
DDW365
Бренд: Ubee Страницы: 88
2N Telekomunikace 2N SmartCOM Quick Manual preview
2N SmartCOM
Бренд: 2N Telekomunikace Страницы: 2
Zte MF659 Quick Manual preview
MF659
Бренд: Zte Страницы: 8
Xerox Fax Modem 4219/MRP Operator'S Manual preview
Fax Modem 4219/MRP
Бренд: Xerox Страницы: 90

Бренды по названию

Популярные бренды

Загрузить еще бренды