manualshive.com logo in svg

Paradyne COMSPHERE 3610, Руководство оператора

Программный инсталляционный руководство для Paradyne COMSPHERE 3610 теперь доступен для загрузки совершенно бесплатно с manualshive.com. Этот manual поможет вам правильно установить необходимое software на ваше устройство, обеспечивая его оптимальную работу. Необходимая информация теперь всегда под рукой!

Поделиться
Скачать
background image

COMSPHERE 3600 Series Data Service Units

Glossary-6

July 1999

3610-A2-GB91-90

Multichannel Multipoint
(MCMP)

A circuit card that enables the support of up to six independent applications over
a single multipoint digital facility. The MCMP capability can support up to 16
tributary DSUs, each optioned (installed) with an MCMP circuit card.

multipoint circuit

A data network circuit that uses multipoint transmission and consists of one
control with multiple tributaries.

NetView

An IBM

r

 program product that is used to monitor and control a network and

diagnose problems.

Network Communications
Control Facility (NCCF)

The NetView command facility that is used to monitor and control network 
operation.

Network Control Program
(NCP)

An IBM program product that runs in a front-end processor and helps virtual
telecommunications access method (VTAM) manage the network.

Network Controller (NC)

An AT&T NMS that uses the DATAPHONE II (DPII) protocol.

Network Management System
(NMS)

A set of diagnostic and configuration management tools for a data communication
network, consisting of software programs and dedicated computer hardware.

Network Problem
Determination Application
(NPDA)

The NetView hardware monitor that gathers information about network error
conditions from devices like NCPs, DSUs, modems, and cluster controllers.

non-disruptive diagnostics

Diagnostics that are transmitted over the in-band secondary channel or routed
through a DBM in Standby mode so that bandwidth assigned to the data is not
affected.

non-disruptive session

Executing the command will not disrupt primary data.

non-modular circuit card

A Model 3611 circuit card (DSU, TDM, or MCMP) with connectors mounted onto
the card. This circuit card type requires that the DTE cables be disconnected before
the circuit card is removed from the carrier.

off-network extension

See extended network.

option sets

Sets of configuration options (or libraries) that are related and fulfill a specific
function. For example, the Diagnostic (Diag branch) configuration options allow
you to configure the DSU for performing diagnostic functions. This option set (or
library) contains 16 configuration options related to the DSU’s or DBM’s diagnostic
operation.

permissive interface

A dial modem operating mode characterized by a fixed output power level of
– 9 dBm. It is one of two possible operating modes for a DBM connected to dial
lines (see programmable interface).

physical address

The shared diagnostic control panel (SDCP) address of a DSU derived from its
carrier address and physical slot number.

physical unit
(PU)

In Systems Network Architecture (SNA), manageable hardware or software that
provides a function for the network (a resource) that manages and controls
communication between other resources in that network.

point-to-point circuit

A data network circuit with one control and one tributary.

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

SWEEX MO128 - QUICK_START_GUIDE Installation Manual preview
MO128 - QUICK_START_GUIDE
Бренд: SWEEX Страницы: 9
TELUS iR1200 Installation Manual preview
iR1200
Бренд: TELUS Страницы: 37
NetComm NB7 Quick Install Manual preview
NB7
Бренд: NetComm Страницы: 2
Zte K4305-Z User Manual preview
K4305-Z
Бренд: Zte Страницы: 9
ABB EDS 500FSD20 Operating Instructions Manual preview
EDS 500FSD20
Бренд: ABB Страницы: 6
D-Link DSL-2740B Brochure & Specs preview
DSL-2740B
Бренд: D-Link Страницы: 3
Panasonic DBS 38 User Manual preview
DBS 38
Бренд: Panasonic Страницы: 6
Panasonic DBS 128 Installation Manual preview
DBS 128
Бренд: Panasonic Страницы: 58
Panasonic Digital Business System User Manual preview
Digital Business System
Бренд: Panasonic Страницы: 87
Panasonic KR20 User Manual preview
KR20
Бренд: Panasonic Страницы: 135
Broadxent Di3631 User Manual preview
Di3631
Бренд: Broadxent Страницы: 60
Comnet netwave NW1 Installation And Operation Manual preview
netwave NW1
Бренд: Comnet Страницы: 46
Telstra MF626i_QRG Quick Reference Manual preview
MF626i_QRG
Бренд: Telstra Страницы: 8
Telstra Business Smart Modem Manual preview
Business Smart Modem
Бренд: Telstra Страницы: 13
AmazonBasics B071Y6Y83W User Manual preview
B071Y6Y83W
Бренд: AmazonBasics Страницы: 17
3Com 3COMIMPACT IQ User Manual preview
3COMIMPACT IQ
Бренд: 3Com Страницы: 160
Zte MF622 Quick User Manual preview
MF622
Бренд: Zte Страницы: 6
Haier Telecom HW-WM100 User Manual preview
HW-WM100
Бренд: Haier Telecom Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды