Paradyne COMSPHERE 3610 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 310

background image

COMSPHERE 3600 Series Data Service Units

1-4

July 1999

3610-A2-GB91-90

Order the COMSPHERE 3600 Series Data Service

Units, Models 3610 and 3611, Dial Backup Module and
SNA Diagnostic Interface Options, Applications Guide if
the Dial Backup Module (DBM) or SNA Diagnostic
Interface options are part of your configuration.

Order the COMSPHERE 3600 Series Data Service

Units, Models 3610 and 3611, Time Division Multiplexer,
Multichannel Multipoint, and Digital Bridge Options,
Applications Guide if your application uses a TDM or
MCMP circuit card, or uses DBM-Vs, DBM-Ss, or
DBM-Ds. The SNA Diagnostic Interface option, as it
applies to these applications, is also covered in this
applications guide.

Feature Description

This section provides descriptions of how to use the

DSUs as local area data sets (LADS), DSU compatibility
with other equipment, the NMS interface, rate adaption,
available diagnostics, in-band secondary channel
transport, network control and tributary addressing, and
aggregate switching.

LADS Operation

The 3600 Series DSUs can be used as a local area data

set (LADS) to provide a point-to-point link between any
two data devices having like protocols.

Multipoint LADS can be achieved by using an extra

DSU with TDM that is configured as an extended or
central-site bridge. The digital bridge essentially
“bridges” multiple point-to-point LADS circuits into a
single front-end processor (FEP). Refer to the
COMSPHERE 3600 Series Data Service Units,
Models

3610 and 3611, Time Division Multiplexer,

Multichannel Multipoint, and Digital Bridge Options,
Applications Guide for more information.

The digital network interfaces connect to a 4-wire,

nonloaded metallic pair. Both point-to-point and bridged
LADS can operate at 2.4, 4.8, 9.6, 19.2, 38.4, 56, or
64 kbps full-duplex. Table 1-1 summarizes the distance
limitations governing use of the 3600 Series DSUs for
LADS operation.

For bridged LADS information, order the

COMSPHERE 3600 Series Data Service Units,
Models 3610 and 3611, Time Division Multiplexer,
Multichannel Multipoint, and Digital Bridge Options,
Applications Guide.

Table 1-1

LADS Connection Distances

Data Rate

Wire Gauge (AWG)

Data Rate

(kbps)

19

22

24

26

2.4

20.0 mi

(32.2 km)

16.6 mi

(26.7 km)

12.7 mi

(20.5 km)

9.4 mi

(15.1 km)

4.8

19.4 mi

(31.2 km)

12.7 mi

(20.5 km)

9.6 mi

(15.4 km)

7.1 mi

(11.5 km)

9.6

15.2 mi

(24.5 km)

9.7 mi

(15.6 km)

7.3 mi

(11.7 km)

5.6 mi

(9.0 km)

19.2

1

11.8 mi

(19.0 km)

7.5 mi

(12.1 km)

5.7 mi

(9.2 km)

4.2 mi

(6.8 km)

38.4

11.2 mi

(18.0 km)

6.5 mi

(10.5 km)

4.6 mi

(7.4 km)

3.2 mi

(5.1 km)

56

9.2 mi

(14.8 km)

5.4 mi

(8.7 km)

3.8 mi

(6.2 km)

2.8 mi

(4.5 km)

64

9.2 mi

(14.8 km)

5.4 mi

(8.7 km)

3.8 mi

(6.2 km)

2.8 mi

(4.5 km)

1

Power level is –10 dBm.

«
...
18
19
20
21
22
...
»

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

Бренд: Novatel Страницы: 35

Бренд: PACH & COMPANY Страницы: 4

Бренд: Ebyte Страницы: 38

Бренд: Black Box Страницы: 101

Бренд: Data-Linc Group Страницы: 27

Business Smart Modem V7610

Бренд: Telstra Страницы: 8

Бренд: LG Innotek Страницы: 20

Бренд: Nokia Страницы: 10

Бренд: Fritz! Страницы: 250

Бренд: B+B SmartWorx Страницы: 2

Бренд: Fritz!Box Страницы: 192

Бренд: Gnet Страницы: 55

MTX-3G-JAVA series

Бренд: MTX Страницы: 109

Бренд: iiNet Страницы: 28

Бренд: Haier Telecom Страницы: 10

Бренд: E3 Страницы: 10

Бренд: Fargo Страницы: 11

Бренд: Magnet Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды