Paradyne COMSPHERE 3610 Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 310

background image

DSU Operations

4-23

3610-A2-GB91-90

July 1999

NOTE

The Digital Test command is not
available when the LPDA-2
configuration option is enabled.

The following selections are displayed:

F1

DSU Digital Tst:
Start

Displ

Clr

F2

F3

If the Digital Test is already in progress, Start will not

be displayed.

For a DSU operating in single-port mode and having

either nondisruptive diagnostics or rate adaption in effect,
an additional selection for Aggr (Aggregate) or Prt1
(Port 1) appears:

F1

Port Number:
Prt1

Aggr

F2

F3

Selecting Aggr (Aggregate) allows only the test pattern

data to propagate the looped data path; in-band secondary
channel transport data is not allowed, thereby disrupting
in-band secondary channel transport communications.
Selecting Prt1 (Port 1) allows both the test pattern and
in-band secondary channel transport data to propagate the
data path; in-band secondary channel transport
communications are preserved.

F1

DSU Address: 1 2 3

Enter

F2

F3

The address of the tributary DSU being tested is

entered if the initiating DSU is a control. (This screen is
not displayed if the DSU is a tributary.)

F1

RunTim:

0:01:09

Enter

F2

F3

In this example, the Digital Test has been set to run for

0 hours, 1 minute, and 9 seconds (format is hhh:mm:ss).
The

and

keys move the cursor to the right or left,

the F1 (

↑

) and F2 (

↓

) keys increment or decrement the

digits where the cursor is positioned. Selecting Enter
issues the DT command and returns you to the DSU
Digital Test screen.

F1

DSU Digital Tst:
Command Complete

F2

F3

The test result is a message indicating whether or not

the loopback executed successfully.

Results

When the message Command Complete is displayed,

any key except the

key returns you to the Digital Test

submenu, where the Dsply and Clr selections display. In
the following example, DT ran for 1 minute and 9 seconds
with no errors and no error seconds.

F1

DSU Digital Tst:
Displ

Clr

F2

F3

To review the results of the test, select Display (Displ)

and press the

key to scroll through the results shown

in

Table 4-6

.

F1

DSU DT: Final
Time:

0:01:09

F2

F3

«
...
101
102
103
104
105
...
»

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

Бренд: Sierra Wireless Страницы: 12

Бренд: FALCOM Страницы: 22

Zlinx ZP9D-115RM-LR

Бренд: Advantech Страницы: 56

Бренд: Corecess Страницы: 14

Бренд: NETGEAR Страницы: 28

Бренд: NXP Semiconductors Страницы: 29

Бренд: LOVATO ELECTRIC Страницы: 8

Бренд: 3Com Страницы: 2

CMX 3CR292-DE56

Бренд: 3Com Страницы: 6

Бренд: 3Com Страницы: 40

Бренд: W&T Electronics Страницы: 63

Бренд: Swarm Страницы: 80

Бренд: Optoma Страницы: 38

Бренд: Embedded Communications Systems Страницы: 43

Бренд: Raymar Страницы: 23

Бренд: NETGEAR Страницы: 23

HomeConnect 3CP3617B

Бренд: 3Com Страницы: 42

TFM-560U - DATA SHEETS

Бренд: TRENDnet Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды