Paradyne COMSPHERE 3610 Скачать руководство пользователя страница 218 | Manualshive

Страница: 218 / 310

background image

COMSPHERE 3600 Series Data Service Units

C-16

July 1999

3610-A2-GB91-90

Table C-10

(3 of 8)

TDM/MCMP/Bridge Configuration Error Messages

Message

Action

Condition

Ext Time undspd

TDM mode: The port selected as the
source of external timing (the
TxClkSource configuration option is
set to port number in the DSU and/or
DBM configuration submenu) is also
an underspeed port.

A port cannot be the source of
external timing and also run
underspeed.

Correct the problem in one of two
ways:

1. Configure another synchronous

port as underspeed via the
appropriate path (DSU or DBM) in
the PrtSp configuration submenu.

2. Configure another port to provide

external timing.

Elast Not Valid

Bridge mode: An attempt is made to
configure a DSU as an extended
bridge with elastic store turned ON at
one or more of the active bridge
ports, and the Bridge Rate
configuration option is set to any
value but =DSU. Bridge Rate is a
configuration option in the Setup path
of the MUX configuration submenu.

For an extended bridge configuration
where Bridge Rate is set to any value
but =DSU, elastic store must be
turned Off at each of the active bridge
supports.

Set configuration option ElasStor
(Elastic Store) to Disab for each of
the active bridge ports via the
appropriate path (Prt2—Prt6) in the
MUX configuration submenu.

FEP Speeds diff

TDM or MCMP mode: The two ports
in the FEP port-sharing group are
assigned to different speeds.

Both ports in an FEP port-sharing
group must be assigned to the same
speed.

Assign the same speed to both ports
in an FEP port-sharing group via the
appropriate path, DSU or DBM, in the
PrtSp configuration submenu.

FEP&ShrDv Incmpt

TDM or MCMP mode: An attempt is
made to place a port into both a
digital-sharing group and an FEP
port-sharing group.

A port cannot be included in a
digital-sharing group and an FEP
port-sharing group at the same time.

Select which of the groups is to have
the port via the Setup path in the
MUX configuration submenu.

Incmpt Diag mode

Mixed diagnostic type is not
compatible with point-to-point or
MCMP operation.

Select another mode of operation via
the Setup path in the MUX
configuration submenu, or select
another diagnostic type via the
Diagnostic DSU or DBM option set.

«
...
216
217
218
219
220
...
»

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

Бренд: PACH & COMPANY Страницы: 4

Бренд: Ebyte Страницы: 38

Бренд: Black Box Страницы: 28

Бренд: Research Страницы: 20

Бренд: NetComm Страницы: 28

Бренд: Zte Страницы: 2

Бренд: Zte Страницы: 12

Бренд: TP-Link Страницы: 24

Бренд: Zte Страницы: 11

Бренд: Billion Страницы: 72

Бренд: Zhone Страницы: 5

Бренд: Blonder tongue Страницы: 12

HFB-FO-LON Series

Бренд: Buenoptic Страницы: 8

Бренд: Four-Faith Страницы: 34

InduBox PSTN III

Бренд: Bausch Datacom Страницы: 24

Бренд: Bausch Datacom Страницы: 27

Бренд: Micro-Aide Страницы: 48

Бренд: Romtelecom Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды