manualshive.com logo in svg

Paradyne COMSPHERE 3610, Руководство оператора

Программный инсталляционный руководство для Paradyne COMSPHERE 3610 теперь доступен для загрузки совершенно бесплатно с manualshive.com. Этот manual поможет вам правильно установить необходимое software на ваше устройство, обеспечивая его оптимальную работу. Необходимая информация теперь всегда под рукой!

Поделиться
Скачать
background image

Configuration Options

6-29

3610-A2-GB91-90

July 1999

Table 6-6

(7 of 8)

General Configuration Options

AnswExtBU: Disab
Next        Enab        Disab        Prev

Answer External Dial Backup. This configuration option is an aggregate switch on-demand feature that
allows dial backup for a point-to-point 3600 Series DSU using an 

external dial backup unit (DBU). The

3600

 

Series DSU is forced to switch the aggregate data to the alternate DTE connector, the interface

connected to the aggregate data path rather than to the DTE (Port 1, either the V.35 or EIA-232-D interface).
Control of the aggregate switch can be automated in several ways.

When the remote site is expected to initiate a dial backup session, AnswExtBU should be enabled. With this
type of automated control, the DSU monitors the data terminal ready (DTR) lead on the aggregate port.
When the 

external DBU has established a call and has turned ON the data set ready (DSR) lead, the DSU

switches the aggregate data from the DDS line to the aggregate port via a crossover cable between the
DBU and the DSU. When the 

external DBU drops the call and the DTR signal is turned Off, the DSU

switches the aggregate data back to the DDS line. Note that when enable is selected, the DCP Backup
(Bkup) or NMS Standby Facility (sf) commands and the DCP Drop Backup (DrBU) or NMS Standby Facility
(sf) commands are ignored.

When a dial backup session is initiated at the local site, AnswExtBU should be disabled so that the DSU
controls the DSR lead on the aggregate port via the DSU’s DCP or the NMS. By selecting the Backup
command from the DCP (Bkup) or Standby Facility (sf) command from the NMS, data is routed from the
external DBU through the aggregate switch to the DTE. As a result, the DSR signal is turned ON, which then
turns on the DTR signal at the 

external DBU. If configured for DTR call-control, the external DBU places the

call. Data is switched back to the DDS line when the DCP Drop Backup (DrBU) or NMS Standby Facility (sf)
command is issued, which turns the DSR signal Off on the aggregate port and, if the 

external DBU is

configured correctly, the DBU drops the dial connection.

If an internal dial backup module (DBM) is installed and active, this configuration option will not be

displayed.

Enab

—

Activates the DSU to automatically switch the aggregate data stream when the DTR signal is
turned ON. The DSU configuration option AggrSwitch must be enabled.

Disab

—

Allows the local DSU to control the call setup and take-down on an 

external DBU via the DSU’s

DCP or the NMS. The DSU configuration option AggrSwitch must be enabled.

RLSD in MCMP:No
Next        Yes        No       Prev

Remote Line Signal Detect in Multichannel Multipoint. Defines whether switched RLSD is required for shared
backup with MCMP to support RLSD detection. This configuration option is only displayed when a Switched
56 DBM is installed.

Yes

—

Switched RLSD is required.

No

—

Switched RLSD is not required.

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

Boca EXPRESS 14.4 User Manual preview
EXPRESS 14.4
Бренд: Boca Страницы: 52
Alcatel onetouch link 4G y858 Quick Start Manual preview
onetouch link 4G y858
Бренд: Alcatel Страницы: 16
Microsoft EA900 Installation Manual preview
EA900
Бренд: Microsoft Страницы: 37
T-Home Comfort Pro S Installation Manual preview
Comfort Pro S
Бренд: T-Home Страницы: 168
ARC CDL-900 Manual preview
CDL-900
Бренд: ARC Страницы: 24
WATSON AC/DC-POWERED USB HUB 4x USB 2.0 Manual preview
AC/DC-POWERED USB HUB 4x USB 2.0
Бренд: WATSON Страницы: 6
Lantronix M110 Series Command Reference Manual preview
M110 Series
Бренд: Lantronix Страницы: 56
Paradyne COMSPHERE DualFlow 3616 User Manual preview
COMSPHERE DualFlow 3616
Бренд: Paradyne Страницы: 139
Spectrum DataScout 3920 Product Manual preview
DataScout 3920
Бренд: Spectrum Страницы: 24
Broadxent Di3631 User Manual preview
Di3631
Бренд: Broadxent Страницы: 60
Enfora Enabler IIG Integration Manual preview
Enabler IIG
Бренд: Enfora Страницы: 73
Patton electronics OnSite 1052 Series Quick Start Manual preview
OnSite 1052 Series
Бренд: Patton electronics Страницы: 4
O2 e169 Manual preview
e169
Бренд: O2 Страницы: 48
Xircom RealPort CardBus Ethernet 10/100 + Modem 56 User Manual preview
RealPort CardBus Ethernet 10/100 + Modem 56
Бренд: Xircom Страницы: 44
Conrad Nano Operating Instructions preview
Nano
Бренд: Conrad Страницы: 4
Conrad 97 24 28 Operating Instructions Manual preview
97 24 28
Бренд: Conrad Страницы: 8
Label i-FeedGoodL LABCH500IP Technical Manual preview
i-FeedGoodL LABCH500IP
Бренд: Label Страницы: 16
NAL A3LA-R-SMA User Manual preview
A3LA-R-SMA
Бренд: NAL Страницы: 158

Бренды по названию

Популярные бренды

Загрузить еще бренды