manualshive.com logo in svg

Paradyne COMSPHERE 3610, Руководство оператора

Программный инсталляционный руководство для Paradyne COMSPHERE 3610 теперь доступен для загрузки совершенно бесплатно с manualshive.com. Этот manual поможет вам правильно установить необходимое software на ваше устройство, обеспечивая его оптимальную работу. Необходимая информация теперь всегда под рукой!

Поделиться
Скачать
background image

COMSPHERE 3600 Series Data Service Units

6-16

July 1999

3610-A2-GB91-90

Table 6-4

(3 of 4)

Diagnostic General Configuration Options

Packet Delay: 0s
Next        0s        1s        2s        5s        Prev

Packet Delay. Controls the time (in seconds) that a DSU or DBM will wait for a packet to complete from an
NMS. This configuration option only appears for a DSU configured as a control.

NOTE: Must be used when the Model 3600 DSU’s diagnostic channel operates over packet switch, satellite

communications, or other facilities that provide extended throughput delays.

0s to

—

Sets the time the DSU or DBM will wait for the NMS to complete its command.

5s

Extend Chan: No
Next        Yes        No        Prev

Extend Main Channel.

3 

 For an extended network, specifies whether there is main channel connectivity 

between the DTE port of the tributary DSU and the DTE port of the extended control DSU. If set to Yes, the
DSUs propagate Test mode conditions across multiple links. Test mode does not propagate over a circuit
configured for disruptive diagnostics.

Yes

—

Set this configuration option to Yes to extend main channel connectivity between the DTE ports
of the tributary and extended DSU in an extended network. A tributary DSU will send Test
mode conditions downstream, while a control DSU will receive/accept the Test mode condition.

No

—

Set this configuration option to No if you do not have an extended network. A control DSU will
not receive/accept the Test mode condition; the condition will be ignored.

Upstrm Port:Prt1
Next        Prt1        Prt2        Prt3        Prt4        Prt5        Prt6        Prev

Upstream Port.

4 

 If an extended control DSU has its DTE interface connected to the tributary DSU or APL

modem and the configuration option Extend Chan is set to Yes, set this configuration option to the upstream
port number. Select Prt1 if the tributary DSU is operating in single-port mode. This configuration option has
an effect only if Diag Type is set to NonD.

Prt1 to —

Selects the upstream port number.

Prt6

M-PtSymPrt:Disab
Next        Enab        Disab        Prev

Multipoint Symmetrical Port. This configuration option enables rate adaption in the tributary DSU to control
direction on a multipoint circuit. It will not appear if a point-to-point circuit or if operating in MCMP mode, and
is not valid when Diag Type is set to Disr.

This configuration option should be enabled when performing multipoint rate adaption (e.g., the port speed is
less than the line speed). It should also be enabled for single-port multipoint nondisruptive diagnostics if the
transmit data rate is required to match the receive data rate. This is generally the case in extended circuit
applications and in multipoint applications where the tributary DSU is configured as a digital-sharing device.

Enab

—

Enable this configuration option when performing multipoint rate adaption or when a multipoint
network is configured for nondisruptive diagnostics and a symmetric port speed is required for
proper DTE operation.

Disab

—

Disables multipoint rate adaption on the tributary control DSU on the tributary control DSU.

3

When in TDM or MCMP mode, or when a multipoint single-port device, or when DiagType is set to Disr or
None, this configuration option does not appear. Instead, it is displayed in the MUX Port configuration
options, under Port 1, and Ports 2—6 must be set independently.

4

When in TDM or MCMP mode, this configuration option does not appear. Instead, it is displayed in the MUX
Port configuration options under Port 1, and Ports 2—6 must be set independently.

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

ICP DAS USA SST-2400EXT User Manual preview
SST-2400EXT
Бренд: ICP DAS USA Страницы: 28
Ebyte E90-DTU 230SL30-GPRS User Manual preview
E90-DTU 230SL30-GPRS
Бренд: Ebyte Страницы: 22
LandCell CDM819u User Manual preview
CDM819u
Бренд: LandCell Страницы: 46
B&B Electronics 1110F Manual preview
1110F
Бренд: B&B Electronics Страницы: 16
Erco & Gener GenPro 15e Instruction Sheet preview
GenPro 15e
Бренд: Erco & Gener Страницы: 4
Multitech V.92 Desktop Modems MultiModem ZDX Specifications preview
V.92 Desktop Modems MultiModem ZDX
Бренд: Multitech Страницы: 2
Sierra Wireless AirCard 550PCS Connection Card User Manual preview
AirCard 550PCS Connection Card
Бренд: Sierra Wireless Страницы: 184
Paradyne StormPort 610 Installation Sheet And Users Manual preview
StormPort 610
Бренд: Paradyne Страницы: 2
Cisco 3G MicroCell User Manual preview
3G MicroCell
Бренд: Cisco Страницы: 20
Zte MG880 User Manual preview
MG880
Бренд: Zte Страницы: 43
QEI UG-1032 Manual preview
UG-1032
Бренд: QEI Страницы: 12
Genesis GEN-127 Technical Manual preview
GEN-127
Бренд: Genesis Страницы: 3
NimbeLink Skywire LTE NL-SW-LTE-S7 Series Manual preview
Skywire LTE NL-SW-LTE-S7 Series
Бренд: NimbeLink Страницы: 16
Hughes HN9200 Installation Manual preview
HN9200
Бренд: Hughes Страницы: 132
AIS AIRCARD 3G Manual preview
AIRCARD 3G
Бренд: AIS Страницы: 14
3Com 3C892 - OfficeConnect ISDN Lan Modem Router User Manual preview
3C892 - OfficeConnect ISDN Lan Modem Router
Бренд: 3Com Страницы: 132
Kantronics KWM-9612 plus Operation Manual preview
KWM-9612 plus
Бренд: Kantronics Страницы: 12
Dataradio HiPR-900 User Manual preview
HiPR-900
Бренд: Dataradio Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды