manualshive.com logo in svg

Paradyne COMSPHERE 3610, Руководство оператора

Программный инсталляционный руководство для Paradyne COMSPHERE 3610 теперь доступен для загрузки совершенно бесплатно с manualshive.com. Этот manual поможет вам правильно установить необходимое software на ваше устройство, обеспечивая его оптимальную работу. Необходимая информация теперь всегда под рукой!

Поделиться
Скачать
background image

COMSPHERE 3600 Series Data Service Units

Glossary-8

July 1999

3610-A2-GB91-90

synchronous transmission

Data transmission that is synchronized by timing signals. Characters are sent at a
fixed rate. This type of transmission is more efficient than asynchronous
transmission.

System Controller (SC)

An AT&T NMS that uses the DATAPHONE II (DPII) protocol.

Systems Network
Architecture
(SNA)

A description of the logical structure, formats, protocols, and operation sequences
that transmit information and control the configuration and operation of an IBM
network.

Time Division Multiplexer
(TDM)

A circuit card that supports time division multiplexing and digital sharing for up to
six ports, and can serve as a digital bridge for multipoint dial backup and multipoint
LADS operation, or can increase digital-sharing capability.

training

The process of negotiating a communication rate between V.32 modems during call
setup.

transmitter

A circuit capable of generating, modulating, and sending a signal for
communication, control, and other purposes.

tributary

A DSU or modem that is, for diagnostic purposes, at a logically subsidiary level in
a hierarchical network. Tributary DSUs in a network receive data from the control
DSU, as well as from any network management system present in the network.

TXD

State of the EIA Transmitted Data lead (V.24 circuit 103).

UL

Underwriters Laboratories, Inc.

USOC

Universal Service Ordering Codes.

Virtual Telecommunications
Access Method (VTAM)

An IBM program product that controls communication and the flow of data in an
SNA network.

winkback detection

In telephone switching systems, a momentary signal state change from control
mode idle (CMI) to data mode idle (DMI), and back to CMI (sometimes referred to
as a “wink start’’).

6-port connector module

A module that is installed on the COMSPHERE 3000 Series Carrier that contains
six 25-pin EIA-232-D DTE connectors. In addition, a 26-pin high-density
connector is located at the top of the connector module to provide the V.35 interface
for either Port 1 or an aggregate data path. (This connector requires a 6-port V.35
interconnect cable to convert the 26-pin high-density interface to the standard V.35
34-pin interface.) The module is used with a modular DSU-TDM or DSU-MCMP
and allows the removal of the modular circuit cards from the front of the carrier
without first disconnecting the DTE cables at the rear of the carrier.

6700 Series Network
Management System
(NMS)

A Paradyne automated network management system that allows an operator to
monitor network conditions, analyze problems, and take restorative measures from
a single personal computer (PC) workstation. This NMS operates in a Microsoft

r

Windows

t

 graphic environment.

6800 Series Network
Management System
(NMS)

A Paradyne automated network management system that allows an operator to
monitor network conditions, analyze problems, and take restorative measures.

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

B&B Electronics Zlinx Xtreme ZXT9-RM User Manual preview
Zlinx Xtreme ZXT9-RM
Бренд: B&B Electronics Страницы: 163
u-blox LISA-C200 User Manual preview
LISA-C200
Бренд: u-blox Страницы: 79
Ericsson GC 75 Preliminary User Manual preview
GC 75
Бренд: Ericsson Страницы: 26
Futurebit MOONLANDER 2 SCRYPT User Manual preview
MOONLANDER 2 SCRYPT
Бренд: Futurebit Страницы: 12
TSI Instruments NETRONIX THIAMIS 8535 Quick Start Manual preview
NETRONIX THIAMIS 8535
Бренд: TSI Instruments Страницы: 4
SG Wireless SGW8100 User Manual preview
SGW8100
Бренд: SG Wireless Страницы: 6
Apantac EDID-EW-H User Manual preview
EDID-EW-H
Бренд: Apantac Страницы: 1
Osaka MTX-63I Integrator'S Manual preview
MTX-63I
Бренд: Osaka Страницы: 50
Zte K3570-Z Quick Start Manual preview
K3570-Z
Бренд: Zte Страницы: 22
German ElectroniX ZAGIL Operation Manual & User Manual preview
ZAGIL
Бренд: German ElectroniX Страницы: 11
3Com 3C871 Quick Start Instructions preview
3C871
Бренд: 3Com Страницы: 15
W&T Electronics 58210 Manual preview
58210
Бренд: W&T Electronics Страницы: 63
ERE D110 User Manual preview
D110
Бренд: ERE Страницы: 17
Fritz! 3390 Quick Manual preview
3390
Бренд: Fritz! Страницы: 2
Skyway SW-10 User Manual preview
SW-10
Бренд: Skyway Страницы: 23
Four-Faith F8914-E User Manual preview
F8914-E
Бренд: Four-Faith Страницы: 26
Uconnect WA-232E User Manual preview
WA-232E
Бренд: Uconnect Страницы: 8
RACOM MD400 Operating Manual preview
MD400
Бренд: RACOM Страницы: 29

Бренды по названию

Популярные бренды

Загрузить еще бренды