manualshive.com logo in svg

Paradyne COMSPHERE 3610, Руководство оператора

Программный инсталляционный руководство для Paradyne COMSPHERE 3610 теперь доступен для загрузки совершенно бесплатно с manualshive.com. Этот manual поможет вам правильно установить необходимое software на ваше устройство, обеспечивая его оптимальную работу. Необходимая информация теперь всегда под рукой!

Поделиться
Скачать
background image

Configuration Options

6-45

3610-A2-GB91-90

July 1999

Table 6-12

(2 of 5)

TDM/MCMP Port (MUX Funct: TDM or MCMP) Configuration Options*

Overspeed: 2.5
Next        1.25        2.5        Prev

Overspeed. Selects the overspeed range of the asynchronous-to-synchronous converter. This configuration
option displays only when TDM mode is selected.

1.25

—

Selects the basic overspeed range. Basic range provides 1.25 % overspeed in the DTE
asynchronous data rate.

2.5

—

Selects the overspeed percentage for extended range. Extended range provides 2.5 %
overspeed in the DTE asynchronous data rate.

RTS Cntrl: DTE
Next        FrcOn        DTE        Prev

Request-to-Send Control. Controls the behavior of the internal RTS lead.

FrcOn —

DSU keeps the internal RTS ON continuously. Any data appearing on the transmitted data
(TXD) lead from the DTE is transmitted immediately. Choose this configuration value for
constant-carrier operation. (Refer to configuration option Transmitter Carrier Select that follows
for a description of constant-carrier operation.)

DTE

—

DSU turns ON RTS when the 

external RTS is turned ON. CTS is turned ON or Off by the

external control signal RTS. Choose this configuration value for switched-carrier operation.
(Refer to configuration option Transmitter Carrier Select that follows for a description of
switched-carrier operation.)

TxCarrSel: Const
Next        Const        Cntrl        Prev

Transmitter Carrier Select.

1

  Enables the TDM or MCMP transmitter circuitry to simulate switched-carrier

operation (using the V.13 codes) on an individual channel. The simulated switched-carrier operation is also
referred to as pseudo-controlled carrier (PCC) mode. It is required for applications where the receiving DTE
expects a raised LSD lead prior to receiving data.

Const

—

Transmit Constant Carrier (constant-carrier operation). The V.13 codes are not sent. The
corresponding remote TDM or MCMP port must be configured for Receiver Constant Carrier or
Mark (RxCarrSel set to Const or Mark). Configure each port in a digital-sharing group for
Constant Carrier operation (TxCarrSel set to Const).

Cntrl

—

Transmit Controlled Carrier (switched-carrier operation, PCC mode). The DSU transmits the
V.13 codes over the DDS line when the port RTS changes state. When RTS is turned ON, the
DSU transmits a code that turns ON LSD at the remote TDM or MCMP port before CTS is
turned ON at the local TDM or MCMP port. When RTS is dropped, the DSU sends a code that
turns Off LSD at the remote TDM or MCMP port. The corresponding remote TDM or MCMP
port must be configured for Receiver Controlled Carrier (RxCarrSel set to Cntrl). This selection
is not valid if the DSU is part of a Digital-Sharing Device (DSD) group. (See the Mark selection
in the configuration option Receiver Carrier Select.)

NOTE: A port may be configured for switched-carrier operation in one direction and constant-carrier

operation in the other direction.

1

For MCMP mode, this configuration option is ignored 

except during dial backup when the MCMP Bckup

configuration option is set to TDM or a V.32 DBM is installed.

* The menu paths for Port 1 through Port 6 are identical.

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

Dynex DX-M102 User Manual preview
DX-M102
Бренд: Dynex Страницы: 16
Ebyte E95-DTU433L 485-V8 Series User Manual preview
E95-DTU433L 485-V8 Series
Бренд: Ebyte Страницы: 19
Access Hitron Installation Manual preview
Hitron
Бренд: Access Страницы: 3
iiNet MobiiBroadband 3G Manual preview
MobiiBroadband 3G
Бренд: iiNet Страницы: 30
Four-Faith F8 14 Series User Manual preview
F8 14 Series
Бренд: Four-Faith Страницы: 49
dji LTE USB User Manual preview
LTE USB
Бренд: dji Страницы: 71
RACOM PROFI MW160 Operating Manual preview
PROFI MW160
Бренд: RACOM Страницы: 27
VCS NetCam1 Manual preview
NetCam1
Бренд: VCS Страницы: 94
netsys NV-700L User Manual preview
NV-700L
Бренд: netsys Страницы: 78
Ebyte E62-DTU (433D30) User Manual preview
E62-DTU (433D30)
Бренд: Ebyte Страницы: 16
Ebyte E800-DTU V8 Series User Manual preview
E800-DTU V8 Series
Бренд: Ebyte Страницы: 17
Ebyte E32-DTU User Manual preview
E32-DTU
Бренд: Ebyte Страницы: 22
Ebyte 900SL30-GPRS User Manual preview
900SL30-GPRS
Бренд: Ebyte Страницы: 22
Paradyne COMSPHERE 3821PLUS Installation Instructions preview
COMSPHERE 3821PLUS
Бренд: Paradyne Страницы: 2
Cermetek CH2124 Manual preview
CH2124
Бренд: Cermetek Страницы: 18
ViaSat SurfBeam 2 Operation Manual preview
SurfBeam 2
Бренд: ViaSat Страницы: 66
Seneca RM169-1 User Manual preview
RM169-1
Бренд: Seneca Страницы: 33
SimCom RS-232 Quick Start Manual preview
RS-232
Бренд: SimCom Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды