Paradyne COMSPHERE 3610 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 310

background image

COMSPHERE 3600 Series Data Service Units

2-10

July 1999

3610-A2-GB91-90

Tributary 3610 DSUs can be configured from an NMS

provided:

•

The Position configuration option is set to Trib
from the DCP

•

The DSU is connected to a control DSU that is
connected to the NMS

The COMSPHERE 6700 or 6800 Series NMS,

which uses the Advanced Diagnostic protocol (ADp),
fully supports configuration of the DSUs. When using
either the DATAPHONE II (DPII) or Diagnostic
MicroComputer (DMC) protocol, the following
limitations apply:

•

Only a subset of the configuration options or other
configuration parameters can be displayed from the
DATAPHONE II System Controller.

•

Only a subset of the configuration options or other
configuration parameters can be displayed from the
ANALYSIS 6510 NMS.

The DATAPHONE II System Controller console

displays 3600 Series DSU configuration options in a
matrix-coded format. The matrix consists of 11 rows,
labeled A through K, and eight columns, labeled 1
through 8. For example, position G6 represents the option
Link Configuration:

•

G6 ON = Pt-Pt

•

G6 Off = M-Pt

For more information on the matrix-coded format

and/or the NMS commands, refer to your NMS
documentation.

DDS (or LADS)
Network Connection

NOTE

Before connecting the DSU to the
DDS network, ensure that
approved primary protectors have
been installed on the circuit in
accordance with Article 800 of the
National Electric Code, NFPA 70,
in the United States and
Section 60 of the Canadian
Electric Code, Part 1, in Canada.

To connect the DSU to the DDS (or LADS) network:

"

Procedure

1. Plug the DDS network interface cable into the

DSU jack labeled LINE (refer to Figure 2-6).

•

U.S. – select either end of the cable

•

Canada – select the 8-pin end

2. Plug the other end of the cable into the modular

jack (USOC RJ48S) provided by the circuit
provider.

If the remote DSU is also connected to the network, the

DSU’s green OK indicator lights and the Alrm indicator
goes off. The Health and Status screen no longer displays
a No Signal message.

If connecting the DSU to a LADS network, there are

distance limitations that govern the use of DSUs on the
network. For further information, refer to the

LADS

Operation

section of Chapter 1.

Figure 2-6. Model 3610 DSU DDS Network

Connection

LADS Connection

If connecting to a (LADS) network, refer to the

LADS

Operation

section of Chapter 1 for distance limitations

governing the use of 3600 Series DSUs for LADS
connections.

«
...
64
65
66
67
68
...
»

Содержание COMSPHERE 3610























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3610

MO128 - QUICK_START_GUIDE

Бренд: SWEEX Страницы: 9

Бренд: Microlink Страницы: 17

eSAM ITRON FC200

Бренд: Intercel Страницы: 12

Бренд: TeleWell Страницы: 131

Бренд: Vega Absolute Страницы: 23

Бренд: Zoom Страницы: 2

Бренд: Zoom Страницы: 2

Бренд: LG Innotek Страницы: 20

Бренд: Fujisoft Страницы: 16

Бренд: Ewave Страницы: 20

Бренд: Four-Faith Страницы: 37

Бренд: FALCOM Страницы: 31

Бренд: Abocom Страницы: 10

Бренд: Campbell Страницы: 48

Бренд: BT Страницы: 19

Бренд: Javad Страницы: 48

WebRunner USB A01-PU2

Бренд: Atlantis Land Страницы: 2

Бренд: Zypcom Страницы: 132

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды