Paradyne ACCULINK 3160 Скачать руководство пользователя страница 214 | Manualshive

Страница: 214 / 296

background image

SNMP MIB Objects

E-2

3160-A2-GB21-80

March 1999

MIB II (RFC 1213)

The objects defined by MIB II are organized into 10 different groups. The
DSU/CSU implements only those groups where the semantics of the group are
applicable to the implementation of a DSU/CSU. The MIB II object groups
supported or not supported by the 3100 Series devices are as follows:

System
Group

Supported.

Interface
Group

Supported for the network interface, the DTE Drop/Insert
(DSX-1) interface, the synchronous data ports, the COM port,
the AUX port, and the MODEM port. Interface statistics
(counters) apply to any port (COM, AUX, or MODEM),
whichever is defined as the SNMP management link.

Address
Translation
Group

Not supported since this group is not supported in MIB II.

IP Group

Supported.

ICMP Group

Supported.

TCP Group

Supported.

UDP Group

Supported.

EGP Group

Not supported since the EGP protocol is not supported by the
DSU/CSU.

Transmissio
n Group

Supported on the T1 interfaces using the DS1/E1 MIB.
Supported on the synchronous data ports using the
RS-232-like MIB. Supported on the COM, AUX, and MODEM
ports using the RS-232-like MIB.

SNMP Group

Supported.

System Group, MIB II

The System Group objects are fully supported by the DSU/CSU. The following
sections provide clarification for objects contained in the System Group where it
is not otherwise clear how the object definition in MIB II is related to the
DSU/CSU. Objects not mentioned are supported as stated in the MIB.

System Group – “sysDescr” Object (system 1)

This object provides the full name and version identification for the system
hardware and software. This object displays the following string:

[

Company Name] T1 DSU/CSU; model xxxx-xx-xxx; S/W Release: yy.yy.yy; H/W

CCA1:

zzzz-zzz; H/W CCA2: zzzz-zzz; Serial number: ssssssss.

Where:

xxxx-xx-xxx represents the full model number of the unit.

yy.yy.yy represents the software revision number of the unit.

zzzz-zzz represents the hardware revision number of the unit.

ssssssss represents the serial number of the unit.

«
...
212
213
214
215
216
...
»

Содержание ACCULINK 3160









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACCULINK 3160

Бренд: D-Link Страницы: 99

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 15

AirPro DWL-6000AP

Бренд: D-Link Страницы: 65

SISPM1040-582-LRT

Бренд: Lantronix Страницы: 2

Бренд: Lantronix Страницы: 7

Maestro E220 Series

Бренд: Lantronix Страницы: 25

Бренд: RadiSys Страницы: 44

Бренд: Ubee Страницы: 9

Бренд: IBA Страницы: 29

Бренд: Analog Devices Страницы: 76

Brocade X6-8 Director

Бренд: Broadcom Страницы: 207

Бренд: Juniper Страницы: 190

Бренд: Watchguard Страницы: 30

Бренд: Keithley Страницы: 71

Бренд: Idis Страницы: 17

IGS-5225-20T4C2X

Бренд: Planet Страницы: 16

NetVanta Analog Modem Dial Backup Interface Module

Бренд: ADTRAN Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды