Paradyne ACCULINK 3160 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 296

background image

Operation

3-28

3160-A2-GB21-80

March 1999

Configuring a Destination for SNMP Traps

A destination must be configured for each SNMP trap manager specified. This
configuration option is displayed for the number of trap managers specified by the
Number of Trap Managers configuration option.

Procedure

To configure an IP address for the SNMP trap manager:

1. From the top-level menu screen, select Cnfig.

2. Select the configuration option set to be copied into the Edit area by using the

appropriate Function key. Use the scroll keys, if necessary.

3. Select Edit.

4. From the Edit screen, press the

key until the Mgmt selection appears on

the screen.

5. Select Mgmt.

F1

Edit:
User

Alarm Mgmt

F2

F3

6. From the Mgmt Config screen, select Trap.

F1

Mgmt Config:
Gen

Trap

F2

F3

7. Press F1 (Next) until the Trap

n IP Address configuration option appears.

8. Press F2 (Edit) to edit the IP address. You have the option of using F3 (Clear)

to reset the IP address to the factory default

000.000.000.000. Refer to

Setting the IP Address

on page 3-21 for more information on setting an IP

address.

9. Press F1 (Next) until the Trap

n Destination configuration appears, and select

the destination for the SNMP trap by using the appropriate Function key. Use
the scroll keys, if necessary.

F1

Trap

n Dst:

Next

None

Com

F2

F3

«
...
60
61
62
63
64
...
»

Содержание ACCULINK 3160









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACCULINK 3160

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 9

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 2

DSL-2540B - ADSL2/2+ Modem With EN Router

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 62

Бренд: National Instruments Страницы: 162

SMART NODE 4950-NCE

Бренд: Patton electronics Страницы: 8

NetLink 2960 RAS

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 2

Pixie-4 Express

Бренд: XIA Страницы: 17

Бренд: RAIDAGE Страницы: 60

EK-FC285 GTX Classified

Бренд: ekwb Страницы: 2

Бренд: Hamlet Страницы: 122

Бренд: Zoom Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды