Paradyne ACCULINK 3160 Скачать руководство пользователя страница 127

Страница: 127 / 296

Maintenance

4-25

3160-A2-GB21-80

March 1999

Starting a DTE Loopback

The DTE Loopback command (DLB) loops the received signal on the DTE
Drop/Insert (DSX-1) port back to the DTE without change.

496-14317-02

CSU

DSU

NETWORK

INTERFACE

DTE

(DSX-1)

DLB

PORT 1

PORT 2

ALL 1s

Procedure

To perform a DTE loopback:

1. From the top-level menu screen, select Test.

2. From the Test screen, select Lpbk.

Test:
Rlpbk Lpbk

Ptrns

3. From the Loopback screen, press the

key until the DLB selection

appears on the screen.

4. Select DLB.

Loopback:
LLB

PLB

DLB

Test Started

appears on Line 2. If a DTE loopback is already in progress,

the

Already Active

message appears. If an invalid combination of

loopbacks is in progress, the error message

Invld Test Combo

appears

(see

Table 4-8

for valid loopback test combinations).

Содержание ACCULINK 3160









































































































































































































































































































Результаты поиска

Содержание ACCULINK 3160

Отзывы:

Похожие инструкции для ACCULINK 3160

Бренды по названию

Популярные бренды

Paradyne ACCULINK 3160, Руководство оператора

Результаты поиска

Содержание ACCULINK 3160

Отзывы:

Похожие инструкции для ACCULINK 3160

Бренды по названию

Популярные бренды