Paradyne ACCULINK 3160 Скачать руководство пользователя страница 99

Страница: 99 / 296

Operation

3-65

3160-A2-GB21-80

March 1999

Resetting the DSU/CSU

Use the Reset command to perform a power-on reset of the DSU/CSU.

Procedure

To reset the DSU/CSU:

1. From the top-level menu screen, press the

key until the Ctrl selection

appears on the screen.

2. Select Ctrl.

3. From the Control screen, press the

key until the Reset selection appears

on the screen.

4. Select Reset.

Control:
ClrReg Reset

5. From the Device Reset screen, press F1 to initiate a reset of the DSU/CSU

(the power-up sequence screen appears). Press F2 instead to return to the
Control screen without initiating a reset.

Device Reset:
Yes

Download Operations

NOTE:

The Download command is for use by service personnel only. Loss of primary
data could result from improper use.

Содержание ACCULINK 3160









































































































































































































































































































Результаты поиска

Содержание ACCULINK 3160

Отзывы:

Похожие инструкции для ACCULINK 3160

Бренды по названию

Популярные бренды

Paradyne ACCULINK 3160, Руководство оператора

Результаты поиска

Содержание ACCULINK 3160

Отзывы:

Похожие инструкции для ACCULINK 3160

Бренды по названию

Популярные бренды