Paradyne ACCULINK 3160 Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 296

background image

Configuration Options

C-7

3160-A2-GB21-80

March 1999

Table C-2.

Port Configuration Options (5 of 5)

Near-end: Disab
Next Disab Maint Send Both Prev

Near-End Performance Statistics. Specifies whether the DSU/CSU maintains near-end
performance statistics and sends performance report messages (PRMs) for a particular
port.

Disab – Disables near-end performance statistics and does not send PRMs.

Maint – Maintains near-end performance statistics for this port.

Send – Sends PRMs over the port’s EDL every second. Each PRM contains the
performance statistics for the previous 4 seconds.

Both – Maintains near-end performance statistics and sends PRMs over the port’s EDL.

NOTES: – This configuration option is only available on 2-port and 4-port

DSU/CSUs.

– This configuration option is not available if

EDL is disabled.

– If the local DSU/CSU is configured to send near-end performance

statistics, then the remote device must be configured to maintain
far-end performance statistics.

Far-end: Disab
Next Disab Maint Prev

Far-End Performance Statistics. Specifies whether to monitor for far-end performance
report messages (PRMs) and maintain far-end performance registers for a particular
port.

Disab – Disables far-end performance statistics.

Maint – Monitors the port’s EDL for PRMs and maintains far-end performance statistics.

NOTES: – This configuration option is only available on 2-port and 4-port

DSU/CSUs.

– This configuration option is not available if

EDL is disabled.

– If the local DSU/CSU is configured to maintain far-end performance

statistics, then the remote device must be configured to send near-end
performance statistics.

Mgmt Link: Disab
Next Enab Disab Prev

EDL Management Link. Specifies whether the EDL management link is enabled for a
particular port. Selecting Enab allows SNMP or Telnet traffic to flow over the 4 kbps
in-band data link provided by EDL.

Enab – Enables the port’s EDL management link.

Disab – Disables the port’s EDL management link.

NOTES: – This configuration option is only available on 2-port and 4-port

DSU/CSUs.

– This configuration option is not available if

EDL is disabled or the FDL is

enabled.

– If the local DSU/CSU’s EDL is enabled, then the remote device’s EDL

must also be enabled.

«
...
149
150
151
152
153
...
»

Содержание ACCULINK 3160









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACCULINK 3160

Бренд: ICP DAS USA Страницы: 14

Бренд: ICP DAS USA Страницы: 25

Бренд: ICP DAS USA Страницы: 15

Бренд: ICP DAS USA Страницы: 8

Бренд: ICP Страницы: 14

Бренд: Alesis Страницы: 46

RUGGEDSWITCH RS900G

Бренд: RuggedCom Страницы: 23

DSL5068EN(1T1R)

Бренд: Aztech Страницы: 40

Бренд: Edgewater Networks Страницы: 7

HHM Series HHM2411

Бренд: TDK Страницы: 2

PCH1 T P Series

Бренд: Parker Страницы: 107

Digital Encoder Plus

Бренд: IDT Страницы: 98

Бренд: Arbor Technology Страницы: 8

Бренд: MEDIATEK Страницы: 166

Бренд: AMD Страницы: 45

Бренд: ICP DAS USA Страницы: 8

Бренд: Penguin Edge Страницы: 2

Бренд: Harman Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды