Paradyne ACCULINK 3160 Скачать руководство пользователя страница 45

Страница: 45 / 296

Operation

3-11

3160-A2-GB21-80

March 1999

Setting Customer Identification

The customer identification is the only identity number you can change. It is used
to uniquely identify the DSU/CSU.

Procedure

To change the customer identification (CID):

1. From the top-level menu, press the

key until the Ctrl selection appears

on the screen.

2. Select Ctrl.

3. From the Control screen, press the

key until the CID selection appears

on the screen.

4. Select CID.

Control:
Reset

CID Passwd

5. Use the

and

keys to position the cursor under the desired character.

You must enter a character before the

moves the cursor to the next

space to the right.

CustID:

xxxxxxxx

Down

Save

6. Enter the desired ID. Press F1 (Up) and F2 (Down) to scroll up and down

through the valid characters/numbers for the customer ID. Valid characters
are 0 through 9, #, -, ., /, A to Z, and blank space. Press F3 (Save) to save
the ID.

Содержание ACCULINK 3160









































































































































































































































































































Результаты поиска

Содержание ACCULINK 3160

Отзывы:

Похожие инструкции для ACCULINK 3160

Бренды по названию

Популярные бренды

Paradyne ACCULINK 3160, Руководство оператора

Результаты поиска

Содержание ACCULINK 3160

Отзывы:

Похожие инструкции для ACCULINK 3160

Бренды по названию

Популярные бренды