Paradyne ACCULINK 3160 Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 296

background image

Configuration Options

C-18

3160-A2-GB21-80

March 1999

User Interface Configuration Options

NOTE:

A circular symbol (

F

) identifies configuration options that are available on

standalone DSU/CSUs only. A triangular symbol (

Y

) identifies configuration

options that are available on carrier-mounted DSU/CSUs only.

Table C-7.

User Interface Configuration Options (1 of 10)

Self-Test: Enab
Next Enab Disab Prev

Initial Self-Test. Specifies whether the DSU/CSU performs a device self-test at power-up
and after a device reset.

Enab – Enables a self-test.

Disab – Disables the self-test.

FP Access: Enab
Next Enab Disab Prev

Front Panel Access. Determines whether front panel access or display is allowed at the
DSU/CSU.

Enab – Allows the front panel to access and display data.

Disab – Prevents the access and display of data.

NOTE:

This configuration option is available on standalone DSU/CSUs only.

F

FP Pass: Disab
Next Enab Disab Prev

Front Panel Pass-Through. Allows dial-out access to a remote DSU/CSU using the front
panel pass-through operation.

Enab – Allows dial-out access to a remote DSU/CSU.

Disab – Prevents dial-out access to a remote DSU/CSU.

NOTE:

This configuration option is available on standalone DSU/CSUs only.

F

Dial-In: Enab
Next Enab Disab Prev

Dial-in Access. Allows dial-in access to the DSU/CSU. For standalone DSU/CSUs,
dial-in access is through the modem port. For carrier-mounted DSU/CSUs, dial-in
access is through an external device that is connected to the communication port.

Enab – Allows dial-in access to the DSU/CSU.

Disab – Prevents dial-in access. Incoming calls to the DSU/CSU are not answered.

NOTE:

To enable Dial-In for carrier-mounted DSU/CSUs, the external device must
be configured for automatic answer and the ComExtDev configuration
option must be enabled.

«
...
160
161
162
163
164
...
»

Содержание ACCULINK 3160









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACCULINK 3160

Professional Series

Бренд: PACOM Страницы: 15

Бренд: 3Com Страницы: 8

8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink

Бренд: Tyco Electronics Страницы: 18

Бренд: Harman Kardon Страницы: 66

Бренд: National Instruments Страницы: 162

Бренд: XAVI Technologies Corp. Страницы: 71

Бренд: Amperes Страницы: 8

Бренд: Lanner Страницы: 109

Бренд: bintec elmeg Страницы: 33

Бренд: APARIAN Страницы: 2

Бренд: Tandy Страницы: 24

Бренд: MFJ Страницы: 11

Бренд: FOR-A Страницы: 2

Бренд: Hunter Страницы: 2

BiPAC 5200S RC Series

Бренд: Billion Страницы: 79

Бренд: Tripp Lite Страницы: 3

Бренд: ZyXEL Communications Страницы: 23

Бренд: Renesas Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды