Paradyne ACCULINK 3160 Скачать руководство пользователя страница 215

Страница: 215 / 296

SNMP MIB Objects

E-3

3160-A2-GB21-80

March 1999

System Group – “sysObjectID” Object (system 2)

This object provides the authoritative identification of the network management
subsystem contained in the unit.

This object displays the following object identifier:

3160

[

Company OID].1.14.2.2.1

3164

[

Company OID].1.14.2.2.2

3165

[

Company OID].1.14.2.2.3

3161

[

Company OID].1.14.2.2.4

System group –”sysContact” Object (system 4)

This object provides a textual identification of the contact person for this
managed node.

System Group – “sysName” Object (system 5)

This object provides an administratively-assigned name for this managed node.

System Group – “sysLocation” Object (system 6)

This object provides the physical location of this node.

System Group – “sysServices” Object (system 7)

This object provides a value which indicates the set of services that are
potentially offered by the DSU/CSU. Only the following values are supported.

physical(1) – Layer 1 functionality for all interfaces.

datalink/subnetwork(2) – Layer 2 functionality (SLIP, PPP) for the COM, AUX,
and MODEM ports.

internet(4) – Layer 3 functionality (IP) for all management links.

end-to-end(8) – Layer 4 functionality (UDP) for all management links.

Therefore, set this object to 15 (the sum of 1 + 2 + 4 + 8).

Содержание ACCULINK 3160









































































































































































































































































































Результаты поиска

Содержание ACCULINK 3160

Отзывы:

Похожие инструкции для ACCULINK 3160

Бренды по названию

Популярные бренды

Paradyne ACCULINK 3160, Руководство оператора

Результаты поиска

Содержание ACCULINK 3160

Отзывы:

Похожие инструкции для ACCULINK 3160

Бренды по названию

Популярные бренды