Paradyne ACCULINK 3160 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 296

background image

Operation

3-51

3160-A2-GB21-80

March 1999

"

Procedure

To enter a password:

1. Use the

and

keys to position the cursor under the desired character.

You must enter a character before the

key moves the cursor to the next

space to the right. The

key is not destructive.

F1

Passwd:

xxxxxxxx

Up

Down

Done

F2

F3

2. Enter the required password. Press F1 (Up) and F2 (Down) to scroll up and

down through the valid characters/numbers for the password. You have five
minutes to enter the correct password before the DSU/CSU ends the
session.

3. Press F3 (Done) to indicate you are done entering the password. If you enter

an invalid password, the message

Invalid Password

appears.

Acquiring/Releasing the User Interface

You can access the user interface from either the front panel, the COM port, the
MODEM port (for standalone DSU/CSUs), or the SDCP (for carrier-mounted
DSU/CSUs). The DSU/CSU allows only one user interface to be active at a time.
The front panel is the default user interface at power-up or after a reset. It is also
the default during a software download or when a failure occurs at either the local
or remote PC interface.

You can switch an inactive user interface to active if:

H

The current active user interface has had no activity (no key was pressed) for
at least five minutes.

H

The active user interface has been released with the Release command.

H

The active interface connection is broken. This includes the call disconnect
for a modem interface or the termination of the front panel emulation program
on a locally-attached PC (if the PC supports DTR) or the termination of the
async terminal interface on a remote or locally attached terminal.

«
...
83
84
85
86
87
...
»

Содержание ACCULINK 3160









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACCULINK 3160

Бренд: Laird Страницы: 36

Бренд: TC Electronic Страницы: 174

Finalizer Express

Бренд: TC Electronic Страницы: 33

Бренд: Klark Teknik Страницы: 50

Бренд: Xilica Audio Design Страницы: 30

Бренд: hilscher Страницы: 154

Бренд: Parker Страницы: 50

Бренд: Ubiquiti Страницы: 20

Бренд: IDT Страницы: 292

RanaSystems 13-0010--001

Бренд: RANA Systems Страницы: 328

Бренд: SYNTEK Страницы: 41

Бренд: Rane Страницы: 128

Бренд: Acard Страницы: 34

Бренд: Shure Страницы: 113

Бренд: ICOP Technology Страницы: 34

Бренд: INNOSILICON Страницы: 11

Бренд: NZXT Страницы: 2

Бренд: JLCooper Electronics Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды