Paradyne ACCULINK 3160 Скачать руководство пользователя страница 163 | Manualshive

Страница: 163 / 296

background image

Configuration Options

C-19

3160-A2-GB21-80

March 1999

Table C-7.

User Interface Configuration Options (2 of 10)

Password: None
Next None Com Modem Both Prev

Password Mode. Activates a password prompt that prevents access until a password is
entered.

None – Does not require a password.

Com – Prompts the communications port user to enter a password.

Modem – Prompts the remote modem port user to enter a password. This selection is
available on standalone DSU/CSUs only.

Both – Prompts both the communications port user and the remote modem port user to
enter a password. This selection is available on standalone DSU/CSUs only.

Com Port: Disab
Next Enab Disab Prev

Setting the Carrier Communication Port. Enables the use of the communication port in
carrier-mounted DSU/CSUs.

Enab – This communication port is enabled.

Disab – The communication port is disabled.

NOTE:

This configuration option is available on carrier-mounted DSU/CSUs
only.

Com Use: ASCII
Next Mgmt ASCII Daisy Term Prev

Communication Port Use. Specifies how the communication port is used.

Mgmt – Configures the communication port as the link to an SNMP or Telnet system.

ASCII – Configures the communication port as a proprietary ASCII port supporting Front
Panel Emulation software and ASCII alarm messages. Only one ASCII communication
port is allowed per 3000 Series carrier.

Daisy – Configures the communication port as an SNMP or Telnet port that is daisy
chained to the auxiliary port of an another 31xx Series device. This selection is available
on standalone DSU/CSUs only.

Term – Configures the communication port as the interface to an async terminal.

«
...
161
162
163
164
165
...
»

Содержание ACCULINK 3160









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACCULINK 3160

Бренд: DBM Страницы: 50

Бренд: E-TOP Страницы: 76

Бренд: iDirect Страницы: 52

Бренд: dixell Страницы: 4

Бренд: NetComm Страницы: 69

Hotwire ATM Line Cards 8335

Бренд: Paradyne Страницы: 132

Бренд: National Instruments Страницы: 130

Бренд: Datasat Страницы: 24

Бренд: Daedalon Страницы: 6

Enterasys Matrix 2G4082-25

Бренд: Enterasys Страницы: 58

Бренд: UfiSpace Страницы: 34

HIRESCHMANN IT MAMMUTHUS MTM8003-FAN

Бренд: Belden Страницы: 84

Mercury FireWire 400

Бренд: OWC Страницы: 2

Бренд: Nexxt Страницы: 2

ULTRIX-FM-NS-1RU

Бренд: Ross Страницы: 5

EK-UNI Holder D5 V3

Бренд: ekwb Страницы: 2

Бренд: Paradyne Страницы: 216

Бренд: Intel Страницы: 469

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды