Paradyne ACCULINK 3160 Скачать руководство пользователя страница 227 | Manualshive

Страница: 227 / 296

background image

SNMP MIB Objects

E-15

3160-A2-GB21-80

March 1999

Near End Group – “dsx1TimeElapsed” Object (dsx1ConfigEntry 3)

Applies to the network interface only. An error status is returned if access is
attempted for the DTE Drop/Insert (DSX-1) interface.

Near End Group – “dsx1ValidIntervals” Object (dsx1ConfigEntry 4)

Applies to the network interface only. An error status is returned if access is
attempted for the DTE Drop/Insert (DSX-1) interface.

Near End Group – “dsx1LineType” Object (dsx1ConfigEntry 5)

This object corresponds to the NET Framing/DTE Framing configuration options
for the T1 interfaces on the DSU/CSU. Only the following values are supported by
the DSU/CSU.

dsx1ESF(2) – Indicates ESF framing.

dsx1D4(2) – Indicates D4 framing.

Near End Group – “dsx1LineCoding” Object (dsx1ConfigEntry 6)

This object corresponds to the NET Coding/DTE Coding configuration options for
the T1 interfaces on the DSU/CSU. Only the following values are supported by
the DSU/CSU.

dsx1B8ZS(2) – Indicates B8ZS line coding.

dsx1AMI(5) – Indicates AMI line coding.

Near End Group – “dsx1SendCode” Object (dsx1ConfigEntry 7)

This object specifies the test patterns/codes being sent over the network
interface. These tests are not supported on the DTE Drop/Insert (DSX-1)
interface. Only the following values are supported by the DSU/CSU.

dsx1SendNoCode(1) – Specifies that the interface is sending normal or
looped data. Setting the interface to this value stops an active “send pattern”
test on the interface. This is the only value supported by the DTE Drop/Insert
(DSX-1) interface.

dsx1SendLineCode(2) – Specifies that the network interface is sending a
Remote Loopback (Rlpbk) LLBUP code. The code is sent for 10 seconds.

dsx1SendResetCode(4) – Specifies that the network interface is sending
Remote Loopback (Rlpbk) LLBDN code. The code is sent for 10 seconds.

dsx1SendQRS(5) – Specifies that the network interface is sending a QRSS
test pattern. The pattern is sent until the test is halted (i.e., setting to
dsx1SendNoCode).

dsx1SendOtherTestPattern(8) – Specifies that the network interface is
sending a 1-in-8 test pattern. The pattern is sent until the test is halted (i.e.,
setting to dsx1SendNoCode).

«
...
225
226
227
228
229
...
»

Содержание ACCULINK 3160









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACCULINK 3160

BB-HGW700A - Network Camera Router

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 18

Бренд: Watchguard Страницы: 39

Бренд: mikroElektronika Страницы: 3

Бренд: Patton electronics Страницы: 12

TE100-S16 - 10/100Mbps Ethernet Switch

Бренд: TRENDnet Страницы: 15

Бренд: Tait Страницы: 8

Бренд: C4i Страницы: 5

Бренд: THOMSON Страницы: 212

Бренд: VCS Страницы: 118

Бренд: Observint Страницы: 117

640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU

Бренд: Intel Страницы: 105

FireWire 800 ExpressCard 34

Бренд: LaCie Страницы: 24

Бренд: Softing Страницы: 16

Бренд: Cypress Semiconductor Страницы: 26

Бренд: Linksys Страницы: 80

X-FireWire Card

Бренд: Apogee Страницы: 32

Бренд: Intel Страницы: 469

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды