Paradyne ACCULINK 3160 Скачать руководство пользователя страница 30

Страница: 30 / 296

Installation

2-6

3160-A2-GB21-80

March 1999

BLACK

RED

GREEN

WHITE

ORANGE

BLUE

GROUND

+ 24 VDC RETURN

+ 24 VDC SOURCE

99-14298-02

DSU/CSU POWER

PLUG

TO CUSTOMER-SUPPLIED BATTERY

Figure 2-9.

+24 Vdc Power Supply Pinouts

Installing the Single –

48 Vdc Power Supply

To install the DSU/CSU using a single source – 48 Vdc SELV power supply, refer
to

Figure 2-10

and use the following procedure.

Procedure

To install the – 48 Vdc single source power supply:

1. Connect the black and red wires to the – 48 Vdc return source.

2. Connect the green wire to a suitable ground.

3. Connect the orange and blue wires to the –

48 Vdc input source.

4. Cut the white wire off at the outer insulation.

5. Plug the power connector into the DSU/CSU.

BLACK

RED

GREEN

WHITE

ORANGE

BLUE

– 48 VDC INPUT

99-14299-02

GROUND

DSU/CSU POWER

PLUG

TO CUSTOMER-SUPPLIED BATTERY

– 48 VDC RETURN

Figure 2-10.

– 48 Vdc Single Source Power Supply Pinouts

Содержание ACCULINK 3160









































































































































































































































































































Результаты поиска

Содержание ACCULINK 3160

Отзывы:

Похожие инструкции для ACCULINK 3160

Бренды по названию

Популярные бренды

Paradyne ACCULINK 3160, Руководство оператора

Результаты поиска

Содержание ACCULINK 3160

Отзывы:

Похожие инструкции для ACCULINK 3160

Бренды по названию

Популярные бренды