background image

 

5-5 

5.3 Procedure for Connecting and Setting Up 

The connection and setting procedure of teh remote I/O system [MEWNET-F] is described as follows. 

5.3.1 Preparation 

Turn OFF all power supply to devices. 
Configure the master stations and slave stations.This section describes an example of the procedure 
using the following 4 stations. 

 

 

Install each station at prescribed positions. 
 
Configure a system which perform the remote I/O control with a master unit, 3 stations, 5 slots and 128 
I/O points. 
This CPU controls the normal I/O area and remote I/O area with totally 8 slots and 176 I/O points. 

 Reference: 

For information on the onstallation of master station system and slave station system,  

                           <FP3/FP10SH/FP10S Hardware Manual ARCT1F300E-1> 
 

Master Station (Master Unit) 

Max. 4 units/1 CPU 

Slave station 

Per 1 master unit (1 path) 
- Max. 32 stations 
- Max. 64 slots 
Per 1 CPU 
- Max. 128 slots 

 Note: 

If the system is not properly configured, an error will be detected when the power turned on. 
[E35] There are units which cannot be installed on a slave station system. 
[E36] Number of slots or number of I/O points is out of range. 

Содержание MEWNET-F









































































































































































Отзывы: