manualshive.com logo in svg

Panasonic MEWNET-F, Техническое руководство

Поделиться
Скачать
Panasonic MEWNET-F Скачать руководство пользователя страница 131

 

9-21 

9.6 LED Status 

Check the CPU, master unit, slave unit, I/O terminal board, I/O terimnal unit and FP I/O link unit for the 
ON/OFF status of their LEDs, then find the cause fo teh error by referring to the table below. 
 

LED status when the system is turned on 

*The CPU of the master station must be started after it is set to the "PROG. mode". 

CPU 

Master 

Slave station 

Contents 

Actions 

 

PROG. 
LED 
(ON) 

COMM./ 
COM. LED 
(Flashing) 

 

COMM./ 
COM. LED 
(Flashing) 

Normal  

 

PROG. 
LED 
(Flashing) 

COMM./ 
COM. LED 
(Flashing) 

 

COMM./ 
COM. LED 
(Flashing) 

There is a slave 
station which is not 
activated although its 
I/O numbers are 
registered in the CPU.
("Slave station 
connection wait mode" 
is activated.Even if the 
CPU goes to the RUN 
mode, the operation 
will not start.)) 

Turn on the power of the 
slave stations which is 
not activated. 
Check the 
communication cable to 
see if it is correctly 
connected. 
Make sure all of the 
slave stations registered 
in the CPU are 
connected.Match all of 
teh settings, then restart 
again. 

Temporary error 
caused by noise. 
(Self-diagnostic code 
E41) 

Restart the system. 

ALARM LED
(ON) 

 

 

Error on the master 
unit. 
(Self-diagnostic code 
E41) 

Please contact us. 

Temporary error 
caused by noise. 

Restart the system. 

ALARM LED
(OFF) 

 

ALARM LED
(ON) 

Error on the slave 
station. 

Please contact us. 

More than 4 master 
units are installed. 

Remove extra master 
units, then restart the 
system. 

COMM. LED
(ON) 

 

 

CPU version is not ver. 
2.0 or later. 
(When using FP3 
CPU) 

Use a CPU whose 
version is Ver. 2.0 or 
later. 
(When using FP3 CPU) 

 

COMM./ 
COM. LED 
(Flashing) 

 

 

 

ALARM LED
(Flashing) 

Units which cannot be 
used for the 
MEWNET-F are 
installed on a slave 
station system. 
(Self-diagnostic code 
E35) 

Reconfigure the slave 
station. Remove any unit 
which cannot be 
installed on the station. 

 

ERROR 
LED 
(ON) 

 

 

 

COMM./ 
COM. LED 
(Flashing) 

Terminal stations are 
not assigned correctly.
(Self-diagnostic code 
E51) 

Both ends of 
communication path 
should be terminal 
stations. 

 
 

Содержание MEWNET-F









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды