manualshive.com logo in svg

Panasonic MEWNET-F, Техническое руководство

Поделиться
Скачать
Panasonic MEWNET-F Скачать руководство пользователя страница 145

 

11-3 

11.2 Overview of FP1 I/O Link Unit 

The FP1 I/O Link Unit is the interface unit for exchanging I/O information between programmable 
controllers "FP2/FP2SH/FP3/FP10SH" and "FP1". 
When the FP1 is connected to the FP2/FP2SH/FP3/FP10SH Remote I/O system [MEWNET-F] via the 
I/O link unit, you can exchange I/O information in the serial communication format, using a 2-conductor 
cable. 
 

11.2.1 Idea of I/O Link 

By connecting the output relays of one programmable controller to the input relays of the other 
programmable controller, the output information on one controller can be treated as the input information 
on the other controller.Exchanging I/O information like this is called "I/O link". 
 
[Example] 
The output relays Y0 to Y7 of "FP1" and the input relays X0 to X7 of "FP2/FP2SH/FP3/FP10SH" are 
connected in parallel as shown in the figure below. 

 

 

Relays Y0 to Y7 correnspond to relays X0 to X7 respectively. If the otuput relay Y3 of "FP1" is turned 
ON, the input relay X3 of "FP2/FP2SH/FP3/FP10SH" will be ON. 
The following sequence control is available with the I/O link. 

 

 
The FP1 I/O link unit is the interface unit for exchanging I/O information between programmable 
controllers "FP2/FP2SH/FP3/FP10SH" and "FP1" connected with a 2-conductor cable using the 
[MEWNET-F]. 

Содержание MEWNET-F









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды