manualshive.com logo in svg

Panasonic MEWNET-F, Техническое руководство

Поделиться
Скачать
Panasonic MEWNET-F Скачать руководство пользователя страница 65

 

5-3 

5.2 Connection Pattern for MEWNET-F 

There are following 6 types (A to F) of patterns for connecting the master station (master unit) and slave 
stations (such as slave units and FP I/O terminal).For the FP2 Multi-wire Link Unit, only the connection 
patterns A and B are available. 

 Note: 

- Do not perform the connections other than the following 6 types. 
- Do not perform star-burst connection. 
- In the diagram below, each station is described as follows. 

 

 

<Master station> 

 

 
<Slave station> 

○

●

Connection port 
Connection port (for a terminal station) 
* On a terminal station, turn on the 
terminal station setting switch. 

5.2.1 Connection Pattern A 

1 transmission line (using port I only), 1 path 

- The terminal station is the master unit (port 1) and the slave station at the end. 
- The connection using the port II only is not possible. 

  Note) FP2 Multi-wire Unit has the port I only. 

5.2.2 Connection Pattern B 

1 transmission line (using port I only), 2 paths 

- The terminal stations are the slave stations at the both ends of each paths. 
- The connection using the port II only is not possible. 

  Note) FP2 Multi-wire Unit has the port I only.

 

5.2.3 Connection Pattern C 

2 transmission lines (using port I and port II), 1 path each 

- The terminal station is the master unit (ports I and II) and the slave station at the end of each 
transmission line.

 

     

Note) FP2 Multi-wire Unit has the port I only.

 

Содержание MEWNET-F









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды