manualshive.com logo in svg

Panasonic MEWNET-F, Техническое руководство

Поделиться
Скачать
Panasonic MEWNET-F Скачать руководство пользователя страница 72

5-10 

5.3.5 Procedure 4   Power Up Sequence 

Turn on the power to the system after completing the installation of the master and slave stations, wiring 
with transmission cables and settings of station numbers and terminal stations. 
Once the power turns one, the remote I/O control will be enalbed, and the operation can be confirmed. 
(The settings on the CPU such as the I/O number allocation are available.) 
 

Confirming the power up and remote I/O control 
Procedure 

1. Power up the remote I/O controlled slave stations. 
2. Set the CPU on the master unit to PROG. mode. 
3. Power up the master station system as the last step. 
Note1) When you power up the master station, the COMM. LED (COM. LED) of all teh stations will flash 

quickly.Please confirm. 

Note2) When teh PROG. LED on the CPU is flashing, the remote I/O map may be already registered. 
 

Confirmation 

When a remote I/O map has not been registered in the CPU, I/O numbers are allocated automatically 
only for the slave stations which have been turned on. (This is called the remote I/O control using 
"Automatic allocation".) 
(1)When starting up the system in the above procedure, the I/O number allocation using "Automatic 
allocation" is as follows in the "Procedure 1" example. 

 

 

 

-The left example is a case that 
various settings such as I/O map and 
base word number are the default 
values. 
-Master station: Master 1 
Base word number: 64 
* The starting number for the I/O 
numbers of slave stations in the 
master 1 system is 640. 

 
(2) The operation turning on/off the I/O of each station can be confirmed by writing a sequence program 
to the CPU of the master station or performing forced input/output. 

 Reference: 

<Chapter 6 Remote I/O Map>, <7.3 Slave Station Connection Confirmation Mode>

 

Содержание MEWNET-F









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды