manualshive.com logo in svg

Panasonic MEWNET-F, Техническое руководство

Поделиться
Скачать
Panasonic MEWNET-F Скачать руководство пользователя страница 61

 

4-9 

4.2 Power Up Sequence 

The procedure for starting the remote I/O system [MEWNET-F] is as follows. 
 
1. Power up all the remote I/O controlled slave stations.  

      ↓ 

2. Power up the master station system (i.e. the system that the master unit is connected). (The remote 
I/O control will be performed for the running slave stations at this point.) 

      ↓

 

3. Set the CPU of the master station system to "RUN mode". 
 
The basic procedure is as above, however, the procedure after the start-up may be different according to 
the settings. 
 

4.2.1 Remote I/O Mapping, Slave Station Connection Confirmation Mode 

If a slave station registered in the remote I/O map has not been turned on, the operation will not start 
until the slave station is turned on although the master station system has been turned on and set in 
"RUN mode" (The PROG. LED of the CPU is blinking during confirmation).  The remote I/O control will 
be perfomred when setting to "RUN mode", if the master station system is turned on after all the 
registered slave stations have been turned on. 

 Reference: 

<7.3 Slave Station Connection Confirmation Mode>

 

4.2.2 Remote I/O Mapping, Slave Station Connection Not Confirmed Mode 

Remote I/O control is performed only for the slave stations which have been already turned on when the 
master station system turns on (3). 
Even if there is a slave station which is not activated when the master unit is turned on, if it has been 
registered in the remote I/O map, it will be controlled by the master unit after it powers up.  

 Reference: <6.2 Automatic I/O Number Allocation and Arbitrary I/O Number Allocation> 

4.2.3 Remote I/O Map Not Registered Mode 

Remote I/O control is performed only for the slave stations which have been already turned on when the 
master station system turns on (2). (Automatic allocation) 
If you turn on the slave stations after turning on the master unit, the CPU on the master station will not 
be able to control the slave stations. You may not allocate I/O numbers in sequence. 
Be sure to trun on the salve stations to be controlled first, then turn on the master station. 
Turn on the master station system after turning on all the salve stations. 

 Reference: 

<6.2  Automatic I/O Number Allocation and Arbitrary I/O Number Allocation>

 

 

  When actually controlling devices, it is recommended to register an remote I/O map. 

 
 

Содержание MEWNET-F









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды