manualshive.com logo in svg

Panasonic MEWNET-F, Техническое руководство

Поделиться
Скачать
Panasonic MEWNET-F Скачать руководство пользователя страница 151

 

11-9 

11.5.2 Wiring to FP2/FP2SH/FP3/FP10SH 

Connect the RS485 interfaces on the I/O link unit and on the other station of the 
FP2/FP2SH/FP3/FP10SH remote I/O system [MEWNT-F] with a 2-conductor cable (VCTF0.75 mm

2

 x 

2C (JIS). 
Connects to the FP2/FP2SH/FP3/FP10SH system via [MEWNET-F].  
 
When connecting the transmission cable, be sure to connect postive (+) to positive, and negative (-) to 
negative of RS485 interfaces. 

 

* Connect one end of the shielded line of the transmission cable to the F.G. terminal, and ground it. 
 

- 

Set the appropriate I/O link units  in the transmission line of [MEWNET-F] as the terminal stations with 

the mode selector switches SW1 & SW2.  

 

 

 Reference:  

For information on the transmission cable specifications, <3.4 Transmission Cable Specifications> 
For information on the connection of transmission cables and the setting of terminal station, <Chapter 5 
Connection for the Remote I/O System> 
 

11.5.3 Wiring of Power Supply 

Supply power to the control unit, expansion unit, I/O link unit from the same power source so that power 
ON and OFF for all units can be performed at teh same time. 

 

 

 Note: 

Do not supply power to the DC power supply type unit from the terminal that supplies power for the input 
of the FP1 control unit or expansion unit. 

Содержание MEWNET-F









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды