manualshive.com logo in svg

Panasonic MEWNET-F, Техническое руководство

Поделиться
Скачать
Panasonic MEWNET-F Скачать руководство пользователя страница 76

6-2 

6.1 Remote I/O Map 

Input/Output of the remote I/O system slave stations are controlled with I/O numbers, as well as the 
input/output in an ordinal system.This I/O number allocation on the remote I/O system [MEWNET-F] is 
called "Remote I/O map". 
This chapter describes the allocation of I/O numbers for slave stations. 
 

6.1.1 Configuration of Remote I/O Map 

I/O numbers are allocated for slave stations as follows. 
 
1. Remote I/O numbers are allocated in order from teh starting address which is assigned to teh master 
unit.  The starting address is called the "Base word number".  A maximum of 4 master units can be 
installed on one master station.  Starting from the master unit closest to the CPU, the master units are 
called "Master 1", "Master 2", "Master 3" and "Master 4". 
I/O numbers are allocated starting with a slave station with the lowest station number.   Station numbers 
can be assigned independently of the connection order.I/O numbers are also allocated in the order of 
station numbers independently of the connection. 
3. I/O numbers are automatically allocated according to the above conditions.(When using the the 
automatic allocation mode) 
  Using the tool software, you can reallocate the base word number, or allocate I/O numbers arbitrarily 
independently of the connection. 

 
 
The usable I/O points for each path when the base word number is the default are as follows. 
 

 

 
If number of I/O points is large, changing the base word number with the tool software enables the area 
used for the path that needs many I/O to be expanded and other areas to be reduced. 
 
 

Содержание MEWNET-F









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды