manualshive.com logo in svg

Panasonic MEWNET-F, Техническое руководство

Поделиться
Скачать
Panasonic MEWNET-F Скачать руководство пользователя страница 162

12-4 

12.3 I/O Allocation 

Item 

Specifications 

No. of I/O points per one I/O link unit 

64 points 

Note1)

 (32 input points & 32 output points) 

Remote I/O map allocation 

32X/32Y 

Note1) When setting the output of the I/O link error flag to ON (available), it is 63 points (31 input points 

& 32 input points). 

 

12.3.1 I/O Numbers 

The example below shows a remote I/O system which one I/O link unit is connected to a FP0 control 
unit.(When the I/O link error flag is off (unavailable)) 

 

 

 
The I/O link unit is recognized as a salve station with 64 I/O points (32 input points & 32 output points 
(32X/32Y)) by the master unit of FP2/FP2SH/FP3/FP10SH.Therefore, the I/O number of the I/O link unit 
from the FP2/FP2SH/FP3/FP10SH is determined by the base word number of the master unit connected 
to the I/O link unit and the station number of the I/O link unit. 
Also, in the remote I/O map, input is allocated first.In the above example, when connecting the I/O link 
unit with the station number 1 to the master unit with the base word number 64, the I/O link area is 
WX64 and 65 (X640 to 65F) for input, and WY66 and 67 (Y660 to 67F) for output from the 
FP2/FP2SH/FP3/FP10SH.Also, when connecting the I/O link unit with the station number 2 as above, 
the I/O link area is WY68 and 69 (X680 to 69F) for input, and WY70 and 71 (Y700 to 71F) for output 
from the FP2/FP2SH/FP3/FP10SH. 
The I/O numbers of the I/O link unit from the FP0 will vary depending on the installed position. 
 

 

 
For example, if Y20 of the FP0 with the station number 1 is turned ON, X640 of the 
FP2/FP2SH/FP3/FP10SH will be ON.If Y660 of the FP2/FP2SH/FP3/FP10SH is turned ON, X20 of the 
FP0 with the station number 1 will be ON.Similarly, if Y20 of the FP0 with the station number 2 is turned 
ON, X680 of the FP2/FP2SH/FP3/FP10SH will be ON, and if Y700 of the FP2/FP2SH/FP3/FP10SH is 
turned ON, X20 of the FP0 with the slave station number 2 will be ON.As above, the I/O link unit is able 
to exchange the I/O information between the FP2/FP2SH/FP3/FP10SH and FP0. 

Содержание MEWNET-F









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды