manualshive.com logo in svg

Panasonic MEWNET-F, Техническое руководство

Поделиться
Скачать
Panasonic MEWNET-F Скачать руководство пользователя страница 154

11-12 

11.6 I/O Allocation 

This section describes the I/O numbers to be used for the "I/O link".How I/O numbers should be 
allocated will depend on whether you are using the FP1 or FP2/FP2SH/FP3/FP10SH. 
On the FP1, I/O number allocated for the I/O link unit is  fixed, however, on the 
FP2/FP2SH/FP3/FP10SH, it will vary depending on teh connection and setting. 

 

11.6.1 I/O Allocation for FP1 

On the FP1, the special area for the I/O link is used.As the I/O numbers are fixed, the location of the I/O 
link unit and the I/O points used by the FP1 do not affect the allocation of the FP1. 
 

<Special I/O for FP1 I/O link> 

I/O type 

I/O No. 

Description 

Input relay 

X70 to X8F (32 points) 

When the corresponding output Y in the FP2/FP2SH/FP3/ 
FP10SH is turned ON, X70 to X8F will go ON. 

Output relay  Y70 to Y8F (32 points) 

When the Y70 to Y8F is turned ON, the corresponding input 
X in the FP2/FP2SH/FP3/FP10SH will go ON. 

 

11.6.2 I/O Allocation for FP2/FP2SH/FP3/FP10SH 

On the FP2/FP2SH/FP3/FP10SH, it is treated as remote I/O.I/O numbers will vary depending on the 
location of the master units (master 1 to 4) and the station numbers for the slave stations of I/O link unit. 
This section describes the number of I/O points of I/O link unit and the allocation. 

 

No. of I/O points 

Occupies 32 input points and 32 output points. 

- 

I/O numbers are first allocated for the input, then for the output. 

- 

When using the "Allocate Remote I/O Map" function of the tool software FPWIN GR, specify "32X32Y". 

 

Allocation example 

Communication path: Master 1 (the closest master unit to the CPU) 
Base word number: 64 (default value) 
I/O link unit station number: No. 1 
In the above situcations, I/O numbers are allocated as follows. 

 
  X640 to X65F (32 input points) 
  Y660 to Y67F (32 output points) 

 
Each I/O relay corresponds as follows: 

 

 

 Reference: 

For information on the remote I/O allocation, <Chapter 6 Remote I/O Map>

 

Содержание MEWNET-F









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды