Panasonic MEWNET-F Скачать руководство пользователя | Manualshive

Страница: 38 / 168

background image

2-20

2.5.1 I/O Terminal Unit Terminals Specifications

Input unit
Terminal layout diagrams

- 16-point type Primary unit (AFP87422)
Expansion unit (AFP87426)

- 8-point type Primary unit (AFP87421)
Expansion unit (AFP87425)

- In case of expansion unit, the terminals of the
RS485 interface (pins 20 and 21 for the 8-point
unit, pins 36 and 37 for the 16-point unit) is N.C.
(Not connected) terminals.These terminals are not
connected internally.

Note:

- Power supply input (24 V) terminal and all (+) terminals are internally connected. Power supply input (0
V) terminal and all (-) terminals are internally connected.When using (+) or (-) terminal as a common
terminal, use the one closest to the output terminal.
- The screw terminals are all M3.5.

Note:

- When using a limit switch with an LED as the input device, be sure that the internal resistance is 15 k

Ω

(SL, QL, VL type)
- Precautions when using an external power supply
- Use an external power supply at 26.4 V DC or less. (It does not work with the power supply for
operating.)
- When using an external power supply at a low voltage, the current may flow to the external power
supply from the 24 V DC for operating even if it is off. Therefore, the leak current should be 1 mA or less
when it is off.

«
...
36
37
38
39
40
...
»

Содержание MEWNET-F









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MEWNET-F

Бренд: FAAC Страницы: 4

Бренд: FAAC Страницы: 52

Бренд: Hama Страницы: 7

Бренд: Hama Страницы: 44

Бренд: RadioMaster Страницы: 10

Бренд: K&K Страницы: 6

Бренд: Oceanic Страницы: 11

Бренд: RAKwireless Страницы: 6

Бренд: ZKTeco Страницы: 11

Бренд: brel-motors Страницы: 2

FX-COMM4NDER MFX3203

Бренд: Magicfx Страницы: 16

Бренд: HANYOUNG NUX Страницы: 4

Бренд: Broadcast Tools Страницы: 39

Бренд: DCU Tecnologic Страницы: 2

Бренд: Nacon Страницы: 46

Markoprint iJET

Бренд: Weber Страницы: 127

Easyflow J7 DN15

Бренд: Neles Страницы: 12

Бренд: Gain Electronic Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды