Panasonic MEWNET-F Скачать руководство пользователя

Страница: 3 / 168

Table of Contents

Before you start

Functions and Restrictions of the Unit............................1-1

1.1 Features and Functions ............................................................................. 1-2

1.2 System Configuration ................................................................................ 1-3

1.2.1 Master Station (Master Unit) ......................................................................1-4

1.2.2 Slave Stations (Slave Unit, I/O Terminal, I/O Terminal Board, etc)...........1-5

1.2.3 Advanced Units Not to be Used for Slave Station System of “MEWNET-F”1-7

1.3 Unit Types.................................................................................................. 1-9

1.3.1 Remote I/O System "MEWNET-F" Components .......................................1-9

1.3.2 Transmission Cable .................................................................................1-10

1.3.3 I/O Cables and Power Supply Cable for I/O Terminal Board "For MIL

Connector Type" ...................................................................................1-10

1.3.4 Expansion Cable for I/O Terminal Unit ....................................................1-10

Part Names and Functions ................................................2-1

2.1 FP2 Multi-wire Link Unit............................................................................. 2-2

2.2 Remote I/O master unit.............................................................................. 2-6

2.2.1 FP3 Remote I/O Master Unit (AFP3742) ...................................................2-6

2.3 Remote I/O Slave Unit ............................................................................... 2-8

2.3.1 FP2 Remote I/O Slave Unit (AFP2745) .....................................................2-8

2.3.2 FP3 Remote I/O Slave Unit (AFP3745) ...................................................2-10

2.4 I/O Terminal Board .................................................................................. 2-12

2.4.1 I/O Terminal Board Terminals Specifications ..........................................2-14

2.5 I/O Terminal Unit...................................................................................... 2-18

2.5.1 I/O Terminal Unit Terminals Specifications..............................................2-20

Unit Specifications .............................................................3-1

3.1 General Specifications (Common to the System)...................................... 3-2

3.2 Performance Specifications (Common to the System) .............................. 3-3

3.3 Rating and Specifications of Components................................................. 3-4

3.3.1 Master Unit.................................................................................................3-4

3.3.2 Slave Unit...................................................................................................3-4

3.3.3 I/O Terminal Board.....................................................................................3-4

3.3.4 I/O Terminal Unit ........................................................................................3-6

3.4 Transmission Cable Specifications............................................................ 3-8

3.4.1 Recommended Cables...............................................................................3-8

3.4.2 Processing the End of Transmission Cables .............................................3-9

3.5 Communication Time............................................................................... 3-10

3.5.1 Remote I/O Scan Time [TR].....................................................................3-10

Содержание MEWNET-F









































































































































































Результаты поиска

Содержание MEWNET-F

Отзывы:

Похожие инструкции для MEWNET-F

Бренды по названию

Популярные бренды

Panasonic MEWNET-F, Техническое руководство

Результаты поиска

Содержание MEWNET-F

Отзывы:

Похожие инструкции для MEWNET-F

Бренды по названию

Популярные бренды