manualshive.com logo in svg

Panasonic MEWNET-F, Техническое руководство

Поделиться
Скачать
Panasonic MEWNET-F Скачать руководство пользователя страница 13

 

1-5 

1.2.2 Slave Stations (Slave Unit, I/O Terminal, I/O Terminal Board, etc) 

The I/O that is controlled by the master station (CPU unit and master unit) on the remote I/O system 
[MEWNET-F] is called 

slave stations

. A maximum of 32 stations can be connected per master unit, and 

up to 4096 points of I/O can be controlled. 

 

- Slave stations can be mixed. The FP3 system or exlusive I/O terminals are also controlled as slave 
stations. There is not restriction on the order of connection and the composition ratio.  
- 

Staton numbers

 are set to each slave station. 

I/O numbers

 are allocated in the order of station 

numbers. It is not neccesary to set station numbers according to the order from the unit closer to the 
master unit. Also, it is no problem there are blanks. 

 

Overview of slave stations 
-FP2/FP3 system (Slave station system) 

  This is the system with a slave unit installed in the CPU slot of the master backplane instead of a CPU 
  unit as "Slave station control part" shown above. (Note1, Note3) An advanced unit (Note2) can be used 
   as "I/O part" as well as I/O unit. 
  "Shared memory access function" is also available. 
  Note1) I/O can be added by connecting expansion backplane as well as the standard system. Up to 3  
               backplanes including a master backplane can be added. 
               Each length of expansion cables should not be longer than 1.2 m each for FP3, and 2.6 m 
               totally for FP2.  
  Note2) There are some advanced units which cannot be used for the slave station system. 

 

 Reference: 

<1.2.3 Advanced Units Not to be Used for Slave Station System of “MEWNET-F”>

 

 
  Note3) The system cannot be controlled only by the slave unit without a master station. 

 
-FP I/O Terminal Unit 

As the [MEWNET-F] FP terminals, there are an I/O terminal board that the input and output are 
combined and an I/O terminal unit (Note) that the input and output are separate. The "Slave station 
control part" and "I/O part" shown in the above figure is contained in a single unit.  
Note) There are an input unit and output unit for the I/O terminal unit. Also, number of controllable points 
can be incrased or the input and output can be combined by connecting expansion units. 

 

-FP0/FP1/FP-M & I/O Link Unit 

The connection to the [MEWNET-F] network can be established by connecting the I/O link unit to 
FP0/FP1/FP-M The I/O of FP0/FP1/FP-M cannot be directly controlled by the master station, however, 
the I/O link area input of FP0/FP1/FP-M can be controlled with FP3 programs, or the remote I/O area 
input of FP3 can be controlled with FP0/FP1/FP-M programs. 

 Reference: 

<Chapter 11, Chpater 12 (Appendix) I/O Link>

 

Содержание MEWNET-F









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды