manualshive.com logo in svg

Panasonic MEWNET-F, Техническое руководство

Поделиться
Скачать
Panasonic MEWNET-F Скачать руководство пользователя страница 11

 

1-3 

1.2 System Configuration 

The remote I/O system [MEWNET-F] is a network which can be configured with master stations (CPU 
unit + master unit) and slave stations (slave unit + I/O unit or various remote I/O exclusive I/O terminal) 
with transmission cables (two-wire cable). The CPU unit of master station controls the I/O (remote I/O) 
slave stations via the master unit. 
*You can connect various kinds of slave stations on a single communication path from a master unit. 
 

For example, the FP2 master unit can be connected to an FP3 slave unit and I/O terminal unit. 

 

 

Configuration requirements 

No. of installed master units per CPU unit 

Max. 4 units 

No. of slave stations per master unit 

Max. 32 stations 

No. of controllable I/O points per master unit 

Note1) 

 

Max. 4096 points 

No. of controllable slots per CPU unit 

Max. 128 slots 

No. of controllable slots per master unit 

Max. 64 slots 

Transmission cable (Two-wire cable) 

VCTF 0.75 mm

2

 x 2C (JIS) or equivalent 

Total transmission distance per port 

Note2) 

 

Max. 700 m 

Note1) It vaires according to the number of maximum cotrollable I/O points of CPU unit. 
Note2) The transmission distance varies according to the used cable and type of unit. 

 

 Reference: 

For the information on the types and combinations of units,  

                              <Chapter 3  Unit Specifications>

 

 

Содержание MEWNET-F









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды