manualshive.com logo in svg

Panasonic MEWNET-F, Техническое руководство

Поделиться
Скачать
Panasonic MEWNET-F Скачать руководство пользователя страница 82

6-8 

6.3 Arbitrary Allocation of Remote I/O Map 

A remote I/O map can be arbitrarily created and generated in the CPU with a tool software 
independently of the actual installation, and remote I/O control can be performed according to the I/O 
map.The precaution when creating a remote I/O map is described below. 

 Note: 

You cannot register an arbitrary remote I/O map with the FP programmer. 
For the details of the operation of the tool software FPWIN GR, creation and registration of I/O map, 
refer to "FPWIN GR Manual". 
 

6.3.1 Setting the Base Word Number 

The base word numbers can be independently reallocated for each master unit. 
The I/O points necessary for each path can be kept, and the width of remote I/O memory area which is 
used for each master and the normal I/O memory area can be changed. 
 

Setting range 

0 to 511 for each master unit (word unit) 
Note) It varies depending on the combination of the CPU unit and master unit. 
 
[Example] When the base word number of master 3 is changed from 112 to 104, the slave station 
connected master 3 can be given with 256 I/O points (1040 to 119F).However, make the setting to meet 
the following restrictions. 
 

Restrictions 

(Last I/O number of normal I/O memory area) < (Base word number of master 1) 
(Base word number of master 1)   < (Base word number of master 2) 
(Base word number of master 2)   < (Base word number of master 3) 
(Base word number of master 3)   < (Base word number of master 4) 
 
[Condition 1] 
Set the base word number from a master unit that is closer to the CPU.   
The base word number of a master unit at location remote from the CPU cannot be set to a value 
smaller than the base word number of a master unit that is closer to the CPU. 

 

 

 

Содержание MEWNET-F









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды